Hi i very much like your design ,I have a 24 inch wood wheel bedini
i am thinking about using a capacitor setup like the one above the
timing is important 30 degrees off the coil being engaged could you send
me a schematic of above 3 coil anamation?
thank you
how is your wind turbine project going?
Hi Mark,
The schematic you are requesting is no different than the John Bedini’s
SSG with capacitor discharge, except I have expanded the idea of maing
it a 3 phase pulse and discharge. If you understand the John Bedini
monopole motor SSG and the capacitor discharge circuit you will know the
exact schematic already, with the exception of the reed switches
triggering the (SCR) discharge. As everyone knows my components will not
match your components if your coils are different. The schematic you
are requesting is simply 3 seperate bedini pulse motor/discharge
circuits around a rotor using the SCR for discharge triggered by a reed
switch.
My wind turbine is on hold but definately not forgotten, the
prototype was successful. I will be building another one hopefully in
the near future.
i have a wheel that has 8 magnets on it i have run it with 4 coils
and was able to get 46% as much output compared to input. the coils are
not arranged 120 degrees apart is that going to cause me problomes
If you look closely at that 3-coil animation, vieing at a slow
speed you will see my (4) magnet ratio to (3) coil is in an arrangement
where all the coils fire independently from one from the other similiar,
but not alike the [Bill] Muller Generator found on the internet. So my
idea on your rotor and coils would not work like my animation. You would
have to have odd number of coils per even number of magnets or
vice-versa even amount of coils with odd amount of magnets.
Happy Experimenting.
Mark
That is very interesting, You are an excessively skilled blogger.
I’ve joined your feed and sit up for in quest of extra of your fantastic
post. Also, I have shared your web site in my social networks
Nice!! The illustrations are awesome.
I feel Inspired to get all my Bedinni
stuff out of the closet. I like the use of wood in your designs, more
affordable option than machining, plus if theres a problem you might
smell it burning before it gets outa control. Great Job!!! Thanks!
I am inspired that you are inspired from my research. If everyone
would put down their ego or pride and share their research to all
mankind, then we would not need the state babysitting humanity whom
certain corporate greed profitting interest are lobbying in keeping
their monolpolizing supply of energy to the slave-villians of their
realm where it just benefits the existance of that state. Anyways I
always wanted to make this thing out of metal or some other hard
material, but after many rotor failures in my R&D I would not dream
to make it out of anything else. Because of the flexibility of the wood I
have saved myself alot of repair work. My design out of wood can absorb
any catastrophic failure. Never had a fire yet, it don’t get hot runs
very cold, puts out a nice cool breeze when at 3000+rpms. Thank you for
your comment.
Could someone help me to send the schematic drawing or clearer
picture of “MAllen7424′s 3-coil Monopole Pulse Motor/ Generator Animated
Schematic” I really interested to build one… need help to send this
information of the schematic and components used to : ahmadnozreen@yahoo.com really appreciate if anyone could help.. thanks
Your presentation is the best I have seen on the internet. I have
built 3 bedini motors so far, but as you know they are in a never ending
state of evolution, always tweaking, faster, better, more powerful,
longer lasting. thanks Rharrison
Hola marcos :
seria tan amable de enviarme un plano con el nombre de los componente
del 3 bobina Mallen 7424 de pulso monopole motor.12 coil es una belleza
estoy tratando de copiarlo me estaria faltando la parte electrica.
un fuerte abrazo.
Love your site.Just came across it 48hrs ago.I’ve been playing
around with the Bedini device for the last 4years now,but I’m very
impressed with the work you’ve done to help the cause.Keep on rockin’.C.
I just found your website for the first time, and I am so happy to
see what you are doing, I will read the material before asking
questions.
Thank you so much for sharing, I wish I would be advanced so much like you man
I’m a beginer, and would like to build one of those “4 coil
monopole”. I’m not good in electronics but would like to build one.
Despite the above circuit is all about charging batteries, my questions =
is there optional power source from the this “4 coil monopole” that we
can use it as generator besides charging batteries. I no this kinda
silly but really appreciate I you guys could feedback to me..
Just wanted to say thanks for putting this site together. Very
impressive stuff! I have built my first bedini motor and am planning to
add a slave coil and start from there. I have very little electical
experience but I find this technology very interesting. Thanks again!
Hi Mark (well done good work)
Being a novice at this i would like to ask you
1. In your trifiler circuit how many batteries would i be able to charge ?
2. If i added 2 more coils what modifications would i need to make to the circuit ?
Thank you for your time
David
Mark, you are a legend for sharing your cleaver ideas on
Bedini/Bearden inventions and for rightly pointing out the fact that the
people are not in control of world affairs, so we need to spread these
ideas ourselves! the government/bankers/oil companies ain’t gonna do it
for us!
I’m developing a arduino program to rotate 3 batteries {charge,
relax, discharge}. I figure if I add this with a solid state charger,
then we have a winner! I’ll post you the code when we are finished. I
see someone was inquiring about this, hopefully this should get some
more action happening!
Hi Duncan, I appreciate your comment on my page and the hard
research I have done to get people out of the subjection of the powers
of the realm. Man is full of earth changing ideas that would change man
from the sufferage, greed and the lust for power of the global elitists.
Their patent system sounds great for the inventor for intellectual
rights of the idea. I feel that this system is flawed and a disgrace to
man. Costs alot of money to patent an idea, which most people can’t
afford without funding. When you do get your idea patented. without
funding you most likely can’t mass produce it because of the cost. So
the ideas are digested in a book, where everyone has access and for the
poor man to get his idea out to the public he must settle to sell the
patent to someone who has money to burn to mass produce it. This
technique of earth changing patents eventually are to be bought by the
powers to be and suppressed by the competitors so they can keep the
monopoly game going and control all global energy and its production.
With Free energy available to man, we would never be in suffrage and beg
for handout benefits from a constituted government. Every one could be
self sufficient and have no need to kidnap the power over some man’s
birth right and the idea of slavery would probably end.
I am so happy that people are building on the idea of the open source
arduino micro-controller. These ideas will eventually free the people
from their suffrage of a manipulated greed infested fraudulent economy
that our modern day Babylon is diseased and plagued by. I hope every man
gets on the band wagon and lets go of their pride to bring real Free
Energy to earth and to all the inhabitants.
I have been experimenting with the SSG and have a setup with 3
coils running, using a 59cm wheel with 18 magnets (neodenium). The
system is working well in regards to energising old batteries,( i have a
vision of using it to charge a bank of batteries to run the house) but
my issue i have is that the energy radiating off the (coils i think) are
causing my nervous system to tense up. I hadnt noticed it initially as i
didnt realise what was happening, until i used a Gauss meter to take
readings near the wheel. it sends the meter off the scale (100
milligauss) at .5m then it drops to the acceptable limit of 3 milligauss
at 1m. What im finding is that long term exposure is having a
detrimental affect on me. So if i could ask this question. Is it
possible to shield the unit from these energies radiating from the unit?
Any help in this matter would be greatly appreciated.
On the one hand, I’m sorry to hear that you’re suffering from EMS
(Electromagnetic Sensitivity) or, the effects consequent of continued
EMF exposure. On the other, it’s great that you’ve identified the
corollary cause. Not many are that observant. Please do a little
research on the amazing emf shielding capacity of metglas ribbon. You
may find the application answer that your looking for there.
Hi David, another idea might be to enclose the unit in an anti
static fabric like 3M velostat. You can buy the stuff in rolls of
varying thicknesses – a couple of layers might do the trick.
It can only happen from the ground up as these devices are merely
being reestablished from their suppression. Your work really helps the
average guy get a handle on how these concepts work.
Thanks!
I’ll pray for your safety, success, prosperity and peace.
found you on jack bauer ts site. not enuff hours in a day eh? the
reason i’m even bothering to sign your page is your willingness to give
your information away.. bless you mate. when i hit the lottery, you’re
on the list.
blessing to you and yours
‘loader
Nice site! Would like to thank you for the idea to use an arduino.
Some time ago i also bought a freeduino ‘bare-bone board’ from modern devices.com
(i now got 6 of them) and installed it for replacing the rotor (since
that is a timing device only which can be done by a arduino). I also
used a arduino to operate 6 relay’s that can switch battary banks from
charging to C20 discharing to a rest period, while monitoring the
battery voltage while in C20 discharge mode, not to get any lower then
12.4V.
Anyways to use a arduino was brought to me tnx to this site, so tnx
to you! if you want to take a look at some devices check for images on http://www.crossway.nl (slow server in my house) grz from holland. Mike
ps. i put a link of the xtranormal video on a popular whistleblower website nice!
I am also a newbe doing a lot of research in this feild, seen many
websites and picked up lot of knowledge from them. I have to say yours
tops them all. I am starting to build a simple one and progress from
there. I’ll be watching for your wesite updates. Again a very impressive
page and I’m sure many, many hours of work.
Thank You Very Much for helping some of us on our way.
You are going well and have done a lot of very good work here.
I am just putting together a team to seriously work in this area and thank you for your lead.
Congratulations and keep up the good work.
I will be happy to keep in touch and share what we learn with you.
I’m a little surprised by the self motivated style of comments
here… observe, tinker, learn, fail, and ultimately enjoy – but please
don’t treat this page like a bandwagon you hope to get on! Doing that
only increases the chances of sites like this to one day disappear. This
page is a rainbow, don’t bring a dark cloud with you, here…
Great website!! I totally like the annimations!! Nice Work, U Rule
I Soon i hope to master the “Freeduino(Arduino)” cirquit,
(let me first read all about it)
Very elaborate site. I am just researching to start on Bedini
circuits. Yours is a wonderful one-stop site for all things. Thanks for
sharing the knowledge.
I have only started my work with the Bedini and Bearden devices and
wanted to see what others were doing. Good job. Once I get the few
basic devices working great and have the time, I will let you know about
larger systems I would like to build.
Good afternoon, great work, your right, i have never seen anyone
scale up the work as you have, fantastic ! I too been slowly scaling up
my work and was wondering if you can send me a clearer copy of the “3
coil monopole pulse motor/generator animated schematic”. or is it
already here on this website? . . . thanks again
The parts list are no different than any other Bedini SSG circuit,
Except for your unique resistor values when you have tuned your circuit.
You must understand the Bedini Motor /Energizer Circuit.
Thanks for your interest in the schematic, please keep me up-to-date on your build.
Thanks for getting back with me Mark, Yes i understand them, i have
build several, however i’m in a build now that combines all the
features in these type of coils with several unique twists. One is
generator coils inbeded in the main coils that when loaded, generate ac
but “REDUCE” loading on the main rotor, cause it to speed up and lower
the AMP draw !. keep you posted . . .
How are you Mark, wondering if you can help me? can you recomend an
inexpensive “solid state relay” that can handle about 2-3Amps and about
100v max .. .TKS
Sorry took so Long Fernando, I am so pre-occupied with the home
front and catching up and preparing for the change of seasons, but I did
a quick look around to try to help you. Look at this link: http://www.mouser.com/catalog/629/1435.pdf
-Mark
I agreat a lot work because i am building too, one (Adams concept)
to be powered by a solar panel. (I am designing a very specail e- solar
powered bike. I have problems with the coil´s driver ; i use 48v but no
way to find a good shematic´s. Iñ´ve got J.P. Naudin Adams design but
no work. I need some help to design a good driver ( complete with a
parallax or similar and connected and managed by a computer. May vbe you
can give a help with it. May be i can use your shemnatic´s to charge mi
A123 by pulses better than with a collecting coils. Bravo for your
job and help to the motor pulses comunity, keep going on thanks
Hello and many thanks for your HUGE efforts in this arena. I have
been researching renewable energy for some time, reading most of the
links on the web / youtube. Which eventually led me to your website.
WOW!!! so much work and you are sharing the research with all…..Thank
you so much. I won’t get political or religious here but if more people
do the same, the whole world over; then the governments, big companies
may just get undermined and the ‘ordinary’man just might be in a
position to take control of our own lives and have a better future. I
work with people in the squatter camps in South Africa….we so NEED
cheaper electricity soooooo bad…hence my research. If I win the lottery
you will get a huge donation from me…..keep up your excellent work.
Kindest regards, Paul.
Just wanted to say thanks for the information found here, you have
put some time and effert into this. I am working on getting my window
motor running on the arduino, just add another circuit and work it
backwards. I will be starting with your code and work from there, I have
some ideas, just need to learn the codeing. Thanks again. Peace Rawbush
My arduino code is strictly written for a SSG circuit with the
diischarge circuit 1:1 ratio, you must under stand how the electronic
circuit works mechanically to understand how to manipulate the
electronic circuit with software code. I basically know the SSG circuit
and the pulse circuit very well and from there I written in Arduino code
(C++) what the circuit does in software code form which mimmicks the
mechanical trigger embedding in the code with the options to manipulate
with code the additional variables of distance of magnet from coil and
how long the switch will be open(amperes) to charge the coil to zero out
the magnetic field from the passing magnet. If you dont build it the
exact how i printed it the variables must be changed to tune the
circuit. Be sure to moniotor the temperature of the transistor running
the motor until you have a range that keeps it at room temperature. It
is very simple in my eyes. Any Questions I will try my best to help!
When I was 10 I asked my parents why we didn’t make our own
electricity. They replied we didn’t have, PG&E did it for us.
Towhich I replied; ” Doesn’t that cost money?”. Long story short, I was
forcedinto silence on the subject or face further punishment! Today I
know the ‘Laws’ aren’t worth the paper upon which they are written! The
‘Greed’ and the ‘Addiction’ just make sure we never know the truth.
Well….. “TOO LATE!” Today I’m 54 and now that ‘Oil’ has a black eye, I
say we ‘kick’em when they’re down!’
You are not alone, I am building the SSG with the trifilar
modification, I have two really nice bicycle wheels and I want one for
my job and one for home! I am scaling a motor that uses timing and
displacement to create not just the radiant reclamation, but to also
serve as a motor to spin a home generator. The Arduino Idea REALLY
intriques me! How do I get more information? Please! Thank you!
Thank you, I wish you luck with your build… As far as I know, I am
the only one with a working bedini motor running on an Arduino. You will
not find any more information on the subject except for what I post on
this page. Everything you need to build one is printed here. Good luck.
Just saying hi, your self description reads like I might write one.
To sum up I just encountered alternative energy ideas Jan of 2010
started with the perendev/steron/searl/ and now have been looking at
Deyo/Bearden/Bedini/Moray/Tesla(of course) and now yourself, and others.
At this point I am just hoping to have some dialogue with someone
wbleepeddoesn’t think (whatever goes through their heads) I’ve lost my
mind.
datos de trabajo con bobinas con regulador integrado
mallen7424 estoy arrmando y he provado con varias bobinas de
diferentes calibbres de alambre y observado que hay bobinas que
responden mejor la primera que hice la hicimos con 600gramos de alambre
no 22 y 600gramos de alambre no 24 enrrollado juntos dando las
siguientes datos el de no 22 nos da 54hms y el de no 24 nos da 30hms ok
esta bobina la acomodamos a un disco con un motor pequeño con 4 imanes
de 2pulgadas de largo con 6mm de ancbleeped por 5 mm de grosor da un
proedio de 80rpm es decir muy bajo pero al cambiarle de polaridad 2
imanes a sur quedando 2 n- 2-s trabaja muncbleepedmas rapido es decir a
unos 1000 revoluciones pero las bobinas que hicimos para hacer uno ya
grande de 1kilo gramo de cada alambre del 23 y 27 con los siguientes
datos el de no 23 da60 ohms y el de y el de no 27 da 260homs pero este
lo pongo de la misma forma a los imanes y trabaja muy despacio hemos
mando hacer 2 cilindros para los imanes de 1 llavara 12 imanes de
3pulgadas de largo con 1/2 de grosor y 1/2 de neodimio grado 42 en un
cilindro de 6″ de grosor para ponerle 1-n-1-s-1-n-1-s- y el otro de 2″
de alto con 6″ de gosor este llavara 16 imanes de los mencionados
anteriormente tratamos de generar lo suficiente para cargar 2 baterias
mas arrastre un motor mediano en ca de lo que hacemos nosotros el tema
es si no funciona de una trabajara de otra modificando sobre la marcha
ya que el cilindro de 3 pulgadas movera al de 2 pulgadas con libertad
sin tocar las bobinas esclavas que alimentan las baterias tengo varias
confuciones sobre las bobinas que den buen rendimiento tu estas ya
adelantado algunos años en esto que nos aconsejas vamos bien o nos
regresamos espero tus consejos y ya subiremos los videos sobre estos
trabajos saludos
estoy en mis primeros pasos he hechos 2 como prinicpiante y he
acavado de terminar el que quiero trabajar ya en forma clave con los
flotadores de carga para 2 baterias como lo tienen aqui ustedes hay unas
preguntas que me gustaria hacerles he ecbleeped 2 ruedas con 4 imanes
de en base de motor lector todos norte y trabajan muy bien la bobina da
54homs la de no 23 y la del no 26 da 30homs de restencia trabaja muy
bien su peso es de 1.200kg. en el carrete juntos pero haciendo pruevas
le invierto 2 imanes polos opuestos lo cual trabaja mas rapido incluso
se oye el osilador cuando esta el polo opuesto es solo pruevas pero ya
ise 2 cilindros de aluminio masizo de 6″ con 6 imanes de 1/2 de grosor x
3pulgadas de largo quiero hacerlo con imanes n-s-n-asi genera muy buen
volatje parejo a este cilindro que me consejan cuanto le puedo poner de
osilador y de esclavos para que tenga suficiente fuerza para mover cosas
grandes como motores de 2 o 4hp el cargador de baterias que tinen el
timer 555 a cuanto carga a otra cosa que observe es los voltajes de
operacion y de trabajo que no tine el diagrama de 2d lo nesecito para
sever cuanto puedo cargar 2 baterias libres y alimentar la de trabajo si
hay alguin que me lo explique se los agradecere saludos y muy buen
trabajo
seguimos sus pasos en varios experimentos sobre sus generadores
esperemos tener algo sustenable para aforontar los huracanes en la
peninsula de yucatan un saludo desde cancun mexico caribe mexicano
It is excellent you have published the 3 coil monopulse using a
non-battery load. I suggest you program your micro-controller arduino in
order to command igbt or mosfet drivers which will replace reed switch
and third coil sensing so you’ll tune deeper your device. In other
words, the software will generate the signals going into 2N3055 base
& SCR gate.
Hi Ken, I am not sure exactly what information you are looking for,
but I believe you are asking me if the ‘Magnet Width’ is covering the
‘Coil Diameter’ and if that is the answer you are looking for I would
have to say, “Yes the magnet width is 3/8 of an inch larger than the
Diameter of the coil”.
Parabens nobre colega , eu acredito em tudo que descreveu, mas uma vez parabens.
eu estou engatinhando nos meus esperimento ainda, mas estou na luta.
por uma energia limpa e livre.
não sou nenhum expert.
Abraços Edgard.
I have just started in my experimentation of the Free Energy world.
My goal is to build up to charging 6KW worth of batteries a day!
With the latest prototype you have shown on this web site, what is
the size/number of 12V/6V batteries you can charge. I do not mind if I
have to make several of these types of motor/chargers, but I would like
an idea of what I am up against.
In my experience and experiments I do believe you can charge any size
bank of batteries from 1.5volts – 18volts. I run my setup and
experiments with 6 -12volt batteries, I believe I can go up to 24volt
but I am not sure because I dont want to take a chance to blow any
components because of lack of funds. Only thing I can say is to keep you
building is that you will be able with no problem charge your
batteries, but my power factor data of input vs output because of lack
of funds in my most recent experiments have not been controlled
experiments to get accurate numbers to give the actual COP.
I do not use any heat sinks in my setup except on my discharge
circuit of the capacitors, which I dont think I needed. Everything stays
room temperature! One day when I get brave I will run my machine at
24volts and measure the temperatures. Hope this helps you.
THE UNIVERSITY OF THE ABSOLUTE
306 North Brooks Street
Room 409
Madison, Wisconsin 53715
ATTENTION; To whom it may concern,
When I first got to Porch Light Properties, I thought they would
really be of an help, but little did I now that Porch Light would turn
into a problem.
I live in Madison, Wisconsin. The people here are a great deal of
trouble, they black mail persons, extort money from persons lead to
believe that they are helping the home-less, but the opposite is true.
They merely extort and use the people that come to this place for real
help and Porch light Properties is a sham what refuses to be of an real
help and support to persons like myself. Porch Light Properties gets
money from the government to house and feed people only, but I can’t
even get the help for Porch Light what I need to help me of my business
and business interests made of a success. And Porch light Properties is a
kind of the government sucking thing getting money from the government
to further derelict persons. I am desiring to get away from this bunch
killers, and that is my need for that is what they are.
But I am writing, to you, in need of your help. I have a research and
development corporation filed in the state of Wisconsin what I have
been trying to make of a success, and I am working on FREE ENERGY types
of the things. I have asked people here to work with me, they are
disinterested and they suck…that is how I think they make their living.
However, I am interested in doing something constructive with my life
what remains when very much interested in the furthering my research
development business.
I am a writer who has developed, already, the many of the very
advanced ideas and I am in the continued interest of my developments of
my mathematical theorie of the TESSERACT and other related forms of the
mathematiques when completely developed what I think can be used to
explain the physical phenomenon of the world when making of an use of a
different kind of a means that means different then the relative and the
quantum mechanical.
And I am interested in the continuance of the development to my
technologically related form of my ideas what have to do with a new kind
of the mathemetiques what I have developed. Another one of my
developments is that one of technological means of the instantaneous
transport, time travel and the other of the forms of the science and
technologies what have to do with the use of light used to precipitate
solid material objects directly from light.
But the trouble remains here, persons are un-friendly and fierce,
insincere, un-helpful and troublesome and most persons around me here
are totally un-motivated to contribute to society and the persons what
surround me are not at all progressive persons, but rather they are not
trust-worth persons who are criminally minded and they have no respect
for me but they harbor contempt and dis-like persons who have different
ideas then theirs when their life is about doing criminal things and my
life is to do of a different and of a contribution’s means.
You can read as related to my ideas having to do with what I think
are the stars what I think are globally lighted and powered made light
and electromagnetiically emissive made so of an use of an industrially
related means lighted and powered of an use of a wholly new and
different kind of the industrial operation what I think, similarly can
be used on planet by the the American Republique using the Teslian
related form of the technology used industrially on this planet so to
electrically and industrially light and power planet earth, similarly,
lighted and powered of an sue of an industrially related electrical
means. You can read as related to my industrially related ideas by going
to one of my web-sites what treats on one of the directions had of my
research and development corporation.
http://www.onthelightoftheworld.com
The problem is that people here in Madison, they are abusers, usurpers,
killer and thugs and I am needful to move away from this community what
is full of skeptics and persons who refuse dialogues and will not take
interest in the any one of the things of my genuine curiosity and
interest. Thy think FREE ENERGY kinds of the related things, a sham.
They fail to realize the reality of PERPETUAL MOTIN a very relating what
yet requires the greater amount of the research and development work
what yet is needed of he phenomenalism.
When the non-support here is that sufficient to allow me of a the
need to escape from this bunch of killers, userpers and liars, I know
this is a bad report what I am giving you about my neighbors what are
hateful, fierce, un-kind, mean, stupid, un-educatable and lazy but
never-the-less the content of my sayings be true. It is true and I am
needful to get away from these people types when having been forced to
live here before I am very poor financially. What I have told you is the
truth of the circumstance but it is the truth necessary to tell and I
am saying, to you, the way the situation really is.
The persons here where I live…they are mockers, doubters and skeptics
and they think FREE ENERGY stuff a fraud, but I do not think so! I am
no longer interested in dealing with dull threatening and stupid people
who will not believe me nor bother to find out and they ruin me of
jokes, un-pleasantness un-concern, dis-respect, selfish dis-interest
dis-regard and ridicule. In my un-happiness and great concern for my
actually safety and life, then I am constrained to make provision to
actually move.
I live in Porch-light Properties in Madison, Wisconsin and have asked
them of their help and concern, but they tell me that my request, of
them, when needfully their help is out-side of the elements of the
MISSION STATEMENT had of Porch Light Properties. When the Porch Light
persons are not that helpful when not willing to go by the rules where I
live, on this account then I am constrained to move away from the
dis-order of the environment where I live, and in this way I am writing
to you because of your like interests in FREE ENERGY types of the
devices, interests and systems.
I am seventy year of age and I am a single male. I am wishing to move
from this environment because of a lack of emotional and of a lack of
supportive common interests and I am completely fed-up with the
mis-crient persons around me who steal clocks from the publique kitchen,
and to me, the all of this behavior on the part of these morons who
refuse to go by the rules…my own opinion is that am finished with
putting up with the Porch Light authorities who are acting in collusion
with the Madison Police to ruin me. The Porch Light persons are in
sympathy with Madison Police who, in fact, like the persons in my
domicile are, in fact, noting more then a bunch of stupid lazy
law-breaking thugs who are completely irresponsible, selfish, mean and
completely worthless when beyond of an interest in being redeemed.
Porch Light has indicated, to me, that they are not wiling to enforce
the rules where I live and this is another motivating factor what
constrains of my decision to move. It is frightening, to me, where I
live when having to be around these fierce kinds thugs where things can
not be discussed who are ruining my life all so bad .
As long as I am of the opinion to move, in light of my interest, then
I am thinking that I should move to to Worcester, Massachusetts because
there are persons in Worcester, Massachusetts who have similar
interests to my self, and since it is of your similar interest then I am
writing, to you, explaining, to you, my situation. and I am writing, to
you, so to gain of your understanding, support and help when
exceedingly interested in relocation . As I have already indicated, I am
interested in relocation because I am no longer willing to live with
persons with no sensitivity to myself when the thugs around me are
dis-interested in any-thing what I have to say and when the freaks
around me refuse to contribute, understand nor help me of my need when
support in my interest is that what is required.
In that continuance…I am writing, to you, needful to find out, from
you, of your willingness and of your interest in my being an help, to
me, to relocate and as related to you persons in Worcester if, at all,
you would be wiling to help of a person such as myself of whom it would
be that would be-friend to a friend, with an mutuality of an interest
what also would be of a benefit, to you, that you would be of an help,
to me, in my exercise of an re-location as we could be of an mutuality
of an help one to the other.
If you would be empathetique to my plight would you please provide me
with names, addresses, telephone numbers and E-mail addresses of
persons that I could work with and of the names, telephone numbers and
E-male addresses of person who wold be of an help, to me, in my
situation. I would appreciate it ever so much. And that I would like,
similarly, to find out as related to the kinds of the accommodations
exist where you are as could be offered t a new-comer and I would,
similarly, like to find out,from you, as t the nature of the projects
what they are being worked on by others also?
The loneliness what experience here with these persons also
up-bearable. I am in the need of finding out about of a re-locate to an
area of the country where I would be appreciated for my talents,
education, knowledge, training and interest and I could help when living
in Worcester. One thing more…I do not have that much money but housing
accommodations made with persons of similar interest would be well
appreciated and we can work together so to stregenthen one another
interests and research
And my telephone number is this one. and if it would be that would
like to converse, with me, I am available for telephone conversation and
any time that you should like to call, I will be here to receive you.
In the closing the more as related t m discoveries; I do not believe
the stellar radiant bodies, including the sun, hot bodies. They seem hot
to the distant observer but under the barrier of the heat what they
exhibit at some distance away from the stellar radiant bodies, they are
cold bodies what are very advanced civilizations.. The stellar radiant
bodies, all, are very advanced cosmological civilizations lighted and
powered of an use of the industrially related means as first discovered
and demonstrated on this planet by Dr. Nikola Tesla, and my opinion is
this planet earth also that one possible to light and power industrially
and electrically, like the stars.
In the interim you can read the content of one my corporation’s web-sites having the URL what tis:
Thank you, and if you were to respond as quickly as possible as it is
that I am eager to complete of the making of the the necessary plans of
the re-vocation…I would like to accelerate of my related form of the
arrangements completed to move to Worcester, Massachusetts, and would
like to do this because that is the business community where the FREE
ENERGY people have elected to congregational to perform.
When younger, I worked very hard so to be able to qualify to receive Social Security benefits.
In that receipt of Social Security benefits; have used the money what
I have received from Social Security to help my-self and to do
something for others what is of an extreme importance, and in this way
alluded, I have discovered that persons will not further assist me of my
honest desire to get free from this ENTITLEMENT.
I think some of the reasons this kind of the negative stuff occurs in
my life is because persons are angry with me because I am a Social
Security recipient getting a pension from the government, and they do
not like that. But my exploiters, similarly, get money from the
government also but they will not help me of my serious attempts at
being financially successful with my business, and the crooks around me
are not using their money what they get from the government used to do
anything to help any-one, at all. I would gladly give up this Social
Security thing if it would be that I had help to develop o my business
related interests what would give me a monetary income what honestly I
have tried to do.
When I came back from California, I made the mis-take of borrowing
money from predator lenders to launch, on-line, my business, and when I
could not pay back the loan then my business became of the failure. My
on-line business interests, then the more of the trouble, and am yet
making of an effort to pay off the debts.
Hi everybody out there in the independent energy research world!
Unfortunately, I can’t simply give away either materials or time,
but if people either wanted to have parts made [for lack of other help
from other sources closer by] or even partnership up on projects, I
would be willing to talk to you, as we here are seeking ways to
eliminate the energy monopoly that has put us so far behind as a nation
and polluted this whole world with smog and toxic wastes of many
different forms.
So long as we can afford to continue to operate, we want to help as
inexpensively as we possibly can and still keep the rent paid. One major
advantage for us if these designs work, is that since all of our
equipment runs on electricity, we could completely eliminate our
electricity bill and that would save up a ton in operating costs!
Working through the circuits myself started with simple SSG… have
arrived at the “monopole ne555 capacitor dump” motor now. The Kromrey
generator is next as I feel this has the most potential. Easy to build,
understand and I think usability.
All one should be looking for is a collapsing magnetic field in a
coil. That is where energy can be tapped and collected….. seemingly
free.
One idea could be to Use One battery as primary and a capacitor bank
to charge. Switching off motor, dump cap charge into battery (while
disconnecting from primary side), run motor etc… and with this drive the
kromrey generator.
Thank you for such usefull information, it was so interesting to have
a look on shown models and animated diagrams. It’s a good job, hope
most of readers feel the same.
I’m interested with Bedini technology for a few years and already have
made a few types of Bedini motors , but can’t allow no one of them to
selfrun or keep it running by replacing source battery with charged one
and back. Do you have any ideas concerning that ?
Also, please , could you send me the drawings of 3 coil monopole
motor/generator ? I’d like to build it and test. Thanks in advance for
any reply,
wish you success in your very important work.
Kirill.
The information you need is in this website. If you have built the
Bedini SSG or any other advanced machines then you already have the
knowledge to build my 3 coil Generator, my schematic will only be a
guide, your geometry and coils will be different than mine, but dont
worry, tuning you already should know. My generator is just like
Bedini’s patent ‘Radiant Energy Energizer’ except with a twist. My
schematic is just his patent x3 with mechanical reed switch discharging
instead of 555 timer in a 3 phase discharging sequence and upon load it
speeds up with limitations. There is nothing complicated about building
it and nothing you don’t already know or have access to for designing
your own version.
I dont have any self running examples to help your concerns. Thank
you for your comment and good luck with your builds. Self running is not
my goal here, just the battery charging and creating light with the HV
pulse and as you can see I am successful at that. I hope my website will
help you move forward in the world of Radiant Energy.
Hi i just wanted to say the animation is great here, I recently
ordered the parts to build me one, I currently have a SSG working an it
works well I found this an would like to try it out but when me the
parts guy got to the caps he asked what type, metal can type? or many
others i didn’t know what to say i’m (newb) so my question is 1uf 600v
an 10uf 600v is it metal can type or one of the others also are these
VDC rated.
I am going to build a motor folowing your schematic ’4 Coil Monopole
Motor setup with 4 master coils’ and am wanting to confirm that your one
makes power
If you have never built John Bedini’s SSG circuit, then I do not
recommend you build any advanced motors. Please save yourself money and
time and study his circuit and referenced material before building
multiple coil motors/energizers.
I’m very greatful to you for everyting your doing, i’m trying to build one my own, however ihavent got a plan.
could you email me a plan for the parts and wires?
I am not sure how to save this stuff on my computer so I can view it
again.I would very much be interested in viewing it again .Will you
email me this page. Thanks and God Bless you for what you are doing.
Jean
The animation is way cool but I couldn’t read the text to figure out part numbers and that switch? Any help would be apreciated.
Thanks
Dale
I have a SSG running right now so I’m ready to try a three coil machine.
Hi Dale,
All the part numbers are the same as the one on my Animation of
Bedini’s patent. The spinning switch is 3 reed switches in a certain
configuration for sequential discharging, you can use any type of
switch, but be sure the timing is exactly the same as you see it to
trigger on the discharge end. If you know a bedini Pulse Charger Circuit
then you should already know what parts are needed. Nothing out of the
ordinary. I just created a 3 phase system out of his patent.
U have a good idea, but I think maybe u are making a mistake, see
that u have the magnets just in one side of the coils, if u put another 4
magnets with south pole on the outside of the coils and unit then with
iron plates u will get more radiant power maybe.
This is the way transformers work with iron laminated cores that
makes a closed magnetic flux, hope u understand. I wonder if it works.
Hi from Costa Rica and Thanks for all the aclaration infos.
Did u ever see the Tesla Hairpin circuits where u can make radiant energy (a lot of it) and light bulbs with it.
see http://www.transformacomm.com
so I want to try charging batteries instead to light bulbs, maybe it is a more efficient way to do it (and easier).
Ok the trafo consumes not less than 2A @120V AC BUT maybe the
batteries will charge very fast and u can archieve better results in
less time, so what u think?
Sorry for the sumption on the current draw, thats the nominal data of
the transformer about 2A @ 120V AC, I have no test it with the Hairpin
circuit yet, so I dont know how much current it will draw from the wall
outlet when the radiant appears. I hope it will be only a few
milliampers and the batteries charges super fast (maybe too fast??), it
is my opinion at this time only. Im waiting for the capacitors that I
buy en Ebay from Ukraine.
I do have some basic readings on my youtube page http://www.youtube.com/user/MAllen7424
during some of the build. My setup changes extremely everytime I work
on my project that changes everything. If I spent all my time taking
voltage readings and experimenting in every stage of the build, I would
never finish my idea on the bench. I dont mean to not advertise all the
information everyone wants to see, I am alone in the R & D of my lab
experiment, I do want to experiment and log all data for everyone, but
it is time consuming and I am anxious to get it finished. Until that
moment comes everyone must please be patient with me. I am very close to
finishing, until that time comes then I will take the time and
concentrate on logging and record data for everyone to see. I am a one
man team with no time to spare. This winter I plan to have it finished
for everyone to see. Thanks for your comment John
Actually to someone who has had a long career in industrial power
control design it just sounds sadly ignorant and self-deceptive.
“Show that it’s wrong”. No, extraordinary claims require
extraordinary proof, and over *unity claims* are as extraordiary as they
come and require very clear evidence. You have to demonstrate your
flying sheep. I don’t have to throw a flock over a cliff to prove the
common understanding that they can’t.
There are *simple* and *direct* methods of measuring the energy flow
to/from the battery but your speadsheets seem to use a convoluted (and
highly unreliable) method based on battery state-of-charge when a
wattmeter would produce very clear (and under unity) results.
Why choose to measure such an important parameter in such an indirect
and unreliable way, particularly when your results flatly contradict a
large body of very well established physics? You know that “Over Unity”
is a radical claim, but perhaps you don’t see just how radical – to
prove this you have to un-prove just about everything else, starting
with the Laws of Thermodynamics. Good luck with that.
If what you claim is true (COP<1) then it should be a very easy
matter to demonstrate that the nett current is flowing TO the battery.
You haven't, and to me it looks like you simply have a systematic
conceptual error.
Consider this; conventional (under unity) devices run down because
they dissipate the original energy as waste heat (eddy currents,
I-squared-R, friction). Now if we happen to have a device that is
neg-entropic (over unity) it will be gaining energy from the
surroundings. So once started what is to prevent this unstable situation
running away with catastrophic results? After all it would have
*negative* losses, the faster it ran the more energy it would aquire –
Ka-boom!
Wow–you have stimulated a very important thought to me–an negative
entropic system might continuously collect energy until boom. I’d never
really thought about that. The reverse, however, is never true. Just
because a car is full of 20 gallons of gasoline with tons of kilojouls
of energy does not mean the continous energy release explodes the
engine. If a a machine has a fixed efficiency of say 110% and the energy
is charging a battery, it will not go boom, it will merely charge the
battery at the 10% rate (whatever VA that is.) I now tend to think of it
in terms of efficiency, and that prevents me from going boom. Whew…
Hi! It’s me, Idaho. I’ll have to spend some time looking this over. I
have researched a lot of this sort of material but haven’t done much as
far as building in the last few years. I’d like to help out and I’ll
try not to get in the way.
Have you ever run into Bill Lyne in New Mexico? He has a fasinating device, I’ll see if I can find it and send it on.
I also have a cd of Thomas Jefferson Jackson See’s material. He was a
friend of Tesla and a brilliant astronomer and math whiz. I’ve had lots
of math and he loses me fast(like everyone should know what the 7th
derivative represents?). Still great stuff on aether theory.
I am also interested in Stan Meyers work and I have a friend that knows Dennis Lee.
Glenn
I’m very impressed with your 12 coil motor charger. You have done an
excellent job. I really appreciate you sharing your experiences and
testing results. It is an inspiration for all of us.
I have started building my own Bedini motor. I’m building the
infrastructure to support a 6 coil motor. As this is my first, I will
start with 1 coil and run tests. Afterwards, I will expand to 6 if the
first looks promising.
Mark, I must admit that I am having trouble finding information on
the internet to support utilizing larger Bedini motors for practical
purposes / home power generation. Bedini’s 10 coil motor is stated to
produce 10 KW of power.
Are you seeing any promising output power that can support Bedini’s
claims to 10KW from a 10 coil system? Yours is largest system I have
been able to find on the internet and is the only that I can find for
such comparisons. Do you see any evidence that a 10-12 coild system
could power a house with a large number of batteries being charged?
Any advice you can offer would be greatly appreciated. Please feel
free to email be directly. I would be happy to share my test results as I
go along.
Hi Preston,
Thank you for your comments on my 12 coil motor/generator. I know of
all your troubles out on the internet are filled with chaotic
misimforming information, this is the reason I have started this web
site to follow my progress in my understanding of the technology.
Only thing I can prove is the there is something there and the bedini
ssg circuit is the basic setup to understand this radiant energy that
Tesla and others had discovered. Only way you will understand it is
study it by building it and understand John Bedini’s ideas and of course
Tom Bearden’s books on energy from the vacuum and other theories that
go along with it.
My project is an experiment using the circuit for experienting with
this captured potential in a pulsed system for which I have made. The
geometry of my project is far smaller in scale than Johns version, where
I would not get that much power, even if I knew exactly how he built
his, my project has small coils in the system which I am sure differs in
the potential power manifested in both our motor/generators’. I see
potential that is definately there to harness, but I regret to tell you
that I have not been to any level of John’s claims only for the reasons
that I am building my own design as far as the geometry which is based
on his circuit experimenting and it is a slow process alone building and
experimenting at my own leisure. I have yet experimented in the
negative entropy theories of his circuit to give you the answer you are
looking for, that I apologize.
Don’t get discouraged, all I can say is that you are on the right
track. The technology is there and always has been there. You just need
to open your mind to access it! …and build it! Advice I marked in red
text in my page some recommendations to get started . Hopefully the rest
of the reading will help.
Once again Thank you!
I didn’t mention on site that I was away from my project for a brief amount of time…so stay tuned!
i am intesively involved in Bedini technology last months but did not
achieved Overunity in any way. Seeing your advanced setups as stated in
the infamous patent, I ask you and i please want to hear a straight
answer.
What the best COP you achieved consistently so far? I need to know, please.
With all do respect!…We all would like to know the straight truth and
to achieve overunity. My project is driven by the ssg circuit.
Everything else is designed by myself for other reasons to gain
knowledge. I did have some test data runs. But obviously you are looking
for einstant satisfaction without doing the reasearch and reading.
Otherwise you would have found some early test results on this page.
Science and technology didn’t build the space shuttle based on what that
one inventer told them it was going to do and how it worked, it took R
& D. Once again I am not looking to build the ‘machine of the
century’. I am building this to gain knowledge in these fields of
Electrical Engineering(EE). Sorry if you are debating with yourself in
deciding if you are going to build one or not based on someone elses
data that could be inacurate.
The only reason people build the SSG is to learn its concept. Your
imagination will take over from there. What is so wrong about learning
something. If you dont want to learn on your own. Dont build one. Go to
Bedini’s site and buy an already-built charger. Believe me I would
answer your question, but I am by myself on this build and I only built
1/4th of the machine planned. Its not finished in other words. When I
get to the point where it is finished and the machine is consistant
without changes then I will take data down to satisfy everyone. I can’t
give you accurate data on a machine that changes weekly from my
upgrades. Anyways don’t take it personal. I would like to display the
data everyone wants to see because I can’t get this thing built fast
enough. Research & Development takes time and money and usually more
than one person on the same project. You can come waste weeks taking
data but I will push you away because I am going to upgrade my ideas on
‘my unique project’ which will change the data results each time. To me
it is not COP>1.0 that I am looking for, it is the knowledge it is
going to give me to advance the ideas. My motor may be running on the
SSG circuit but one thing I am not looking for is overunity. I am
looking for knowledge that our education system somehow took away from
us. My grandfather knew how to build a motor/generator when he was in
grammer school. And I at 37 had to learn from others including John
Bedini & Tom Bearden and many other knowledge seeking people on the
internet. Only thing that education taught me was to be on time and play
the game by their rules only…or you will fail!
My Motor/Generator Experiment Lab is not an SSG. It is driven by the
SSG circuit respectively and it is once again only a test lab machine of
multiple ssg circuits that happens to be the drive circuit I chose in
teaching myself about Motors/Generators, Radiant Energy… An All-In-One
Test Lab. I am not looking for COP>1.0 I am simply looking for
knowledge. If I achieve over unity or COP>1.0 then great!… at this
point I am not concerned of free energy. If I achieve it then my readers
and the people that are watching me will know as soon as I know. I am
just sharing my researched knowledge and sharing my progress on my
Motor/Generator.
Everyone building the one coil bedini circuit has it easy!… try messing
with 12 or more circuits with multiple triggering sequences and
multiple discharging sequences, you will understand what I am going
through. I have questions and a whole mess load of them. It is very easy
to get mis-lead on false information. I just went to the extreme
because the project wouldn’t have been challenging enough to only build
one coil system. Everyone is building that, why not build 144 coil
system… I bet you can find multiple branches of ideas just because of
the scale of the system with a variety of different results and
different possible applications that go along with its unique geometry.
Thanks for the prompt reply sir. I assure you not many people
involved in OU projects are willing to share their experience in pursue
of overunity.
Ok i understand that you are NOT after achieving C.O.P. over 1 in
electrical terms and did not meant to upset you or distract you from
your studies.
Personally, i am attracted to bedini technology (as most people do)
because he claims that achieving OU is a relatively easy task. (although
most people i know involved have miserably failed.)
for me proving my self that i could “generate energy” from vaccum etc
will be a turning point in my life. I think you understand the
implications. Last, there are is a saying that goes as “believe or not,
do the research”. I am researching! I stick to the rules blindly. I try
without success till today.
On the other hand, i do not want to be a cult member that is ghosted by the OU dream that actually have not ever experienced.
Anyway, you need not to replay this. Finally from a backyarder
reasearcher point of view, i feel an urge to congratulate you for your
great mechanical skills and considerable effort presented in this site.
Great instruction on muti coils, your contribution is priceless
Hello MAllen:
I have seen 1000′s videos.
Yours in one of the top vid on youtube.
Because, multi coil motor is what we are looking for power and torque
that really can change how we use energy through out the world.
Your name will be remembered by 1000′s, Thedaftman,Lidmotor, Hohnydavpro and you ! That really make differance.
Free energy is on our way.
Your detail guiding instruction will help us all.
Re: Great instruction on muti coils, your contribution is priceless
Thank you Ed,
I dont think mine is at the top, but I appreciate the gesture! There
are many great inventors and tinkerer’s out there to see. They all are
great for sharing and expanding our knowledge in the search for the
ultimate creative moment in our lives. You are right, we do need to
create a better sustainable life here on earth away from the
war-mongers, Free Energy would be that change needed. I hope someone is
fast in getting us there honestly, for the love of humanity. I am
trying!… thats all I can say in my contribution.
Hello MAllen7424,
I am impressed with your animation. I will look forward to your future
experiments. Your list of materials is also excellent for building and
reproving purposes. Most sceptics say the power is coming from the
batteries. When will it be a self running power generator with out
batteries?
Thank you for your comment. I have spent alot of time deciphering the
crap on the internet and I have compiled the information that I found
to lead myself up to get me building. I have posted this information to
help people get started quicker so they dont spend a year researching
before building one like I did.
I believe, but do not quote me on this because I am NOT an Electrical
Engineer or physicist, that the energy comes from everywhere in the
circuit …from the callapse of the magnetic field , to the spark of the
transistor (splitting the positives) and even in the diodes and
resistors. I believe the correct term in my reading is “Negative
Entropy” is the source.
The battery?… I dunno could be just and antennae that needs to be
tuned to the receiver like a Ham Radio operator will use an SWR meter to
tune his antannae to his radio gear consisting of variable capacitors
and trimming length of wire to get the tuned wave length. I believe all
these variables come in play here. Which lead to very difficult tuning
procedures. In my 12 pole my circuits all have the the exact same length
of wire everywhere because technically I have 12 seperate bedini
circuits in my configuration. And knowing a bit of Ham radio. I built
based on keeping the length of wire consitant in length through the
circuits for the end result to adjust only one length of wire coming out
of the collectors or from Magnetic Coupling of coils (induction) to be a
bit controlled for tuning in the final testing and experimenting.
My 12 pole monopole motor I have built is not in my goal to create
free energy, but to learn for myself because Electrical Engineering in
my generation of education was not an option for me. So I took the
liberty to build this unit to teach myself about electric motors,
generators, Alternators and configuration thereof (Delta,Wye) and also
this Radiant Energy. In the process I have taught myself basic
electronics and used my mechanical drafting skills and IT Technician
knowledge to build an experiment machine that is flexible for all these
experiments in these fields of science and physics.
I practically live out of a suitcase and dont have a permanent lab or
workshop. My workspace consists of a 1 square yard of table space. So
instead of building multiple motors and generators and prototype
experiment models that I dont have no working or storage space for, I
have engineered this one machine that fits in my small work space to
help teach myself about all these fields of Electrical Engineeering and
physics behind it.
I will be seperated from my experiments for a couple of months. In
the meantime I will be gathering research and doing my best to help the
people of the world understand this as I learn it for myself. Again…I
don’t claim anything here. It is just research for humanity. People will
classify me but I dont care! I know my mind is concious and powerful. I
just hope I have helped people to open their minds a bit more quickly.
The mass confusion of information on the internet with all the debunkers
and deniers falsifying information out there only to convince people to
not think for themselves. Even if I never create this “free energy” In
my experiments by trial and error with this machine I have over come
‘Lenz Law’ by bypassing the effect. If thats not progress and
inspirational I dunno what is!….. Keep thinking for yourself and never
trust the Mass-Media!
Oh, I almost forgot to mention: not only has anyone seemingly
bothered to connect a wattmeter to the battery that, is it claimed, is
only used “initially,” but everyone also seems to have forgotten that
various integrated circuits within the system incorporate active
components that draw yet more power via VCC (BJT technology) / VDD
(MOSFET technology). Someone really must teach this John fellow about
the very fundamentals of electronics!
I read the patent application. He succeeded in finding an imbecile
of an examiner, sure enough: even the initial “explanation” of how a
motor works–describing how a “stator magnet” MUST attract a “rotor
magnet” and overcome such-and-such drag to keep going–describes a
hysteresis motor and ONLY a hysteresis motor. At that, it’s a p*ss-poor
explanation . . .
First, the author here of this web site is not John Bedini. It is
someone who read his instructions on how to build the device mentioned
in his patent. It looks like this site is just a way for the builder of
the device to share his experiences.
Second, obviously no one is as smart as you. You seem to have it all
figured out. I will make a suggestion, instead of taking the time to
develop an entire essay about this guy, prove John Bedini wrong by
building his device (exactly as he states) and then comment. Don’t act
pious and talk down to everyone as if you know and they don’t.
Lastly, you seem to have a lot of anger in your post. When you make
personal attacks, nobody will listen. Stick to the technical discussion
and make your points.
Jesus is not in this conversation, so we can leave him out from this point forward.
I know I will get hit with some dis-believers and debunkers, it is ok
when they post negative comments…in fact I encourage it! If they were
smart enough they will realize the more they write their opinions and
scientific knowledge about my project or even free energy on this
webpage with their big point gathering scrabble words then the more this
website will show up on a search engine top 10 to expose to the world
that we don’t have to be enslaved by the power hungry and the scrabble
trophy holders. So everyone give me all you got! You won’t hurt my
feelings. This site and server is paid for by me. they cant cancel my
subscription to spread the truth or even the research.
I answer to no one on this webpage. Dump your knowledge here and your
links. I will keep all negative and positive comments free to the
people, because the world will benefit from it.
Hm . . . I guess nobody here has the least understanding of
electromagnetic theory. Magnetic fields are solenoidal, meaning that the
field contours emerge from a north pole and return to a south pole. One
can play games with topology so that only the north poles are exposed
to a given armature circuit, but there will be zero flux linkage with
that armature circuit and, consequently, no generated EMF from any
changes to that flux linkage. I cannot help but notice that the putative
“genius electrical engineer,” John Bedini, has difficulty spelling the
most basic EE terminology; has zero understanding of high-school-level
calculus; and states that “reactive power means di/dt.” I have no
concept what the last of those statements might mean, but it sounds like
a rather gross misunderstanding of the general concept that reactive
components of current will be in quadrature phase to real components
thereof, which is also true of the derivative (only if resolved onto an
orthonormal frequency set basis, e.g., a Fourier expansion). Has anybody
taken a look at what’s going on with the batteries and the power
transistor and other things? Also, despite all these mentions of “Lenz’s
Law” and such, I notice flagrant omissions from the putatively complete
circuit diagram. Why don’t we include the ENTIRE system, and we’ll see
where the energy comes from and where it goes. I’m reminded of a
professor who used to stump sophomore circuits students with a simple
capacitor-charging circuit and the question, “where did the energy go”
when the initial and final electric field energies differ (I guess the
students never heard of DOING WORK AGAINST AN ELECTRIC FIELD TO MOVE
CHARGES FROM ONE CAPACITOR TO ANOTHER). This is such utter nonsense that
it’s almost beneath commenting upon. And, of course, it’s such great
technology, that’s why major firms have invested at least $0 to test it.
Do you think they would spend a few dollars to build it were there ANY
remotely serious claim to validity? Sorry to ramble
quasi-ungrammatically, but I get angry thinking about how people here
violate the commandment in Leviticus, “Thou shalt not . . . set a
stumblingblock [sic] before the blind.” Oh, and the comments about
“longitudinal waves” that are “not measurable” by our instruments are
just utter nonsense.
Mr. Bedini, why don’t you post a COMPLETE circuit diagram for the
ignorant–one that doesn’t leave unexplained black boxes floating around
here and there while claiming that subsystem X “generates energy from
nowhere.” I’m delighted that you achieved various things as a youngster
and have had some success screwing with patents, but I hasten to note
that a friend of mine quite literally patented amplitude modulation (by
[a] calling it an Internet Aggregator and [b] finding a patent examiner
who had zero understanding of how to trace signal spectra through a
linear system)–you know, what happens with sidebands, aliasing, mixers,
LPFs, block conversion, Hilbert transformers, things of that nature.
I also have a magic energy generating device that makes a motor spin
and doesn’t have to be plugged in. You take the motor and connect its
armature leads (the field circuit is parallel to the armature circuit)
to a “magic” box that is clearly labeled “DON’T LOOK INSIDE HERE–IT
ISN’T PART OF THE SYSTEM.”
J*sus Chr*st have mercy on the hopelessly ignorant . . .
I am building the basic charger right now and have seen some of your
videos and am very impressed. I am curious though, as the scoolgirl
motor is not designed to develop torque (so I’m told), what is your aim
with this setup? Are you able to charge more batteries with the many
coils? I am not trying to be critical in any way, just curious about
where you are going as I am not always the most perceptive
I am just learning this stuff and have been trying to comtemplate some
of the applications of this circuitry and device although I have not
completed my first charger yet (coil wire is backordered), but hope to
within the next few weeks.
I have heard the window motor has some of the same capabilities to
charge batteries, but also develops torque. Any thoughts on this?
Also came across a guy on Youtube names Dan Quale (pronounced kwalee)
who developed a free spinning generator design which might lend itself
to this type of motor.
Also, have been looking into the gray tube a bit and noticed a comment by a guy named robert calloway here: http://www.keelynet.com about bedini’s circuits and the use of a spark gap to increase potential. Interesting stuff.
Then came across this document: http://www.tfcbooks.com which goes into how tesla used the spark gap with magnets to increase the frequency of the discharge with lower potentials.
I’m not sure how all of this stuff fits together, but I thought you
might be interested as it all seems very related to capturing and
harnessing radiant energy. Keep up the good work.
Re: Welcome
Hi Mark,
Thanks for sharing so much information about the Bedini monople motor. Really good animation!
I’m just getting started building the battery charger and monopole motor
charger shown in the book “Free Energy Generation” by Tom Bearden. Its a
good read.
I will keep you posted as to my progress.
Again, thanks for all your hard work and sharing, Ron.
Hi, great job with your concise schematics. Do you have any email
address? I tried to build a bedini SSG with 2 separate bifilar coils and
the circuits completely separate, except for the 2 batteries. Did you
try this? Some tuning help would be welcomed. Thanks
Hello Sir, Following a different video I saw on your invention, I
took the liberty to contact you. I am a businessman who has just sold
his business and wish to take a new professional direction in relation
to the struggle for global warming and the fight against pollution. I
would have liked to share with you a simple idea which I think for
years: the marketing of an invention for individuals (a lower price)
providing a supply of energy to meet their needs with no pollution. This
revolution, if it existed help solve real soon reversed pollution. I’ve
already find funding to equip a unlimited credit every home, even those
low-income … So that we can disseminate this invention throughout the
world. I think it has long since the easiest way to quickly change the
pollution of the planet, is to provide individuals with an invention
energy "free" to help protect the environment, their purchasing power
and their comfort. The need for information in an average home is
between 5kVA and 30kVA. I am 42 years 4 children, very seriously with
full powers to promote a concept as you see at the European level more …
I’m trilingual, master the intricacies of the sale, communication,
concepts in accounting and legal, with excellent presentation and
extensive experience as a consultant (adviser) for (development
oriented) and the Internet communication ( website, search engine …) …
The relational acquired and cultivated throughout my short career to
have my support is very important in my project … If your skill and
invention are as interesting as it sounds I am concerned by our
complementarity. With your knowledge with me and I know we could do
"off" your invention. So if you thought your invention can be compatible
with my "dream" … Pending the answer to my question and your feelings
about this possible collaboration, Best regards Thierry Morin Fool is
the one who invented a great thing because he just thought it was
possible ADDRESS: Thierry Morin 31 rte de royan The 17,400 EGUILLES
FRANCE Mobile: 33 6 88 07 26 42 email: thierry-morin@hotmail.fr
Hi i very much like your design ,I have a 24 inch wood wheel bedini i am thinking about using a capacitor setup like the one above the timing is important 30 degrees off the coil being engaged could you send me a schematic of above 3 coil anamation?
thank you
how is your wind turbine project going?
i am sory i thought your wind turbine was a new project i should have looked at the date of video
Hi Mark,
The schematic you are requesting is no different than the John Bedini’s SSG with capacitor discharge, except I have expanded the idea of maing it a 3 phase pulse and discharge. If you understand the John Bedini monopole motor SSG and the capacitor discharge circuit you will know the exact schematic already, with the exception of the reed switches triggering the (SCR) discharge. As everyone knows my components will not match your components if your coils are different. The schematic you are requesting is simply 3 seperate bedini pulse motor/discharge circuits around a rotor using the SCR for discharge triggered by a reed switch.
My wind turbine is on hold but definately not forgotten, the prototype was successful. I will be building another one hopefully in the near future.
i have a wheel that has 8 magnets on it i have run it with 4 coils and was able to get 46% as much output compared to input. the coils are not arranged 120 degrees apart is that going to cause me problomes
If you look closely at that 3-coil animation, vieing at a slow speed you will see my (4) magnet ratio to (3) coil is in an arrangement where all the coils fire independently from one from the other similiar, but not alike the [Bill] Muller Generator found on the internet. So my idea on your rotor and coils would not work like my animation. You would have to have odd number of coils per even number of magnets or vice-versa even amount of coils with odd amount of magnets.
Happy Experimenting.
Mark
That is very interesting, You are an excessively skilled blogger.
I’ve joined your feed and sit up for in quest of extra of your fantastic post. Also, I have shared your web site in my social networks
Hi Charlie, Thanks for the post, glad my site sparked some interest!
Nice!! The illustrations are awesome.
I feel Inspired to get all my Bedinni
stuff out of the closet. I like the use of wood in your designs, more affordable option than machining, plus if theres a problem you might smell it burning before it gets outa control. Great Job!!! Thanks!
Hi Leonard,
I am inspired that you are inspired from my research. If everyone would put down their ego or pride and share their research to all mankind, then we would not need the state babysitting humanity whom certain corporate greed profitting interest are lobbying in keeping their monolpolizing supply of energy to the slave-villians of their realm where it just benefits the existance of that state. Anyways I always wanted to make this thing out of metal or some other hard material, but after many rotor failures in my R&D I would not dream to make it out of anything else. Because of the flexibility of the wood I have saved myself alot of repair work. My design out of wood can absorb any catastrophic failure. Never had a fire yet, it don’t get hot runs very cold, puts out a nice cool breeze when at 3000+rpms. Thank you for your comment.
Could someone help me to send the schematic drawing or clearer picture of “MAllen7424′s 3-coil Monopole Pulse Motor/ Generator Animated Schematic” I really interested to build one… need help to send this information of the schematic and components used to : ahmadnozreen@yahoo.com really appreciate if anyone could help.. thanks
Your presentation is the best I have seen on the internet. I have built 3 bedini motors so far, but as you know they are in a never ending state of evolution, always tweaking, faster, better, more powerful, longer lasting. thanks Rharrison
Hola marcos :
seria tan amable de enviarme un plano con el nombre de los componente del 3 bobina Mallen 7424 de pulso monopole motor.12 coil es una belleza estoy tratando de copiarlo me estaria faltando la parte electrica.
un fuerte abrazo.
Love your site.Just came across it 48hrs ago.I’ve been playing around with the Bedini device for the last 4years now,but I’m very impressed with the work you’ve done to help the cause.Keep on rockin’.C.
I just found your website for the first time, and I am so happy to see what you are doing, I will read the material before asking questions.
Thank you so much for sharing, I wish I would be advanced so much like you man
Micha
Dear All,
I’m a beginer, and would like to build one of those “4 coil monopole”. I’m not good in electronics but would like to build one. Despite the above circuit is all about charging batteries, my questions = is there optional power source from the this “4 coil monopole” that we can use it as generator besides charging batteries. I no this kinda silly but really appreciate I you guys could feedback to me..
Regards,
Reen..
Malaysia..
Just wanted to say thanks for putting this site together. Very impressive stuff! I have built my first bedini motor and am planning to add a slave coil and start from there. I have very little electical experience but I find this technology very interesting. Thanks again!
Glad to see that you got the bandwidth issue over the last few days dealt with.
very interesting! well done, I am Italian and I want to come back often to read all the news. greeting
Hi Mark (well done good work)
Being a novice at this i would like to ask you
1. In your trifiler circuit how many batteries would i be able to charge ?
2. If i added 2 more coils what modifications would i need to make to the circuit ?
Thank you for your time
David
Mark, you are a legend for sharing your cleaver ideas on Bedini/Bearden inventions and for rightly pointing out the fact that the people are not in control of world affairs, so we need to spread these ideas ourselves! the government/bankers/oil companies ain’t gonna do it for us!
I’m developing a arduino program to rotate 3 batteries {charge, relax, discharge}. I figure if I add this with a solid state charger, then we have a winner! I’ll post you the code when we are finished. I see someone was inquiring about this, hopefully this should get some more action happening!
Hi Duncan, I appreciate your comment on my page and the hard research I have done to get people out of the subjection of the powers of the realm. Man is full of earth changing ideas that would change man from the sufferage, greed and the lust for power of the global elitists. Their patent system sounds great for the inventor for intellectual rights of the idea. I feel that this system is flawed and a disgrace to man. Costs alot of money to patent an idea, which most people can’t afford without funding. When you do get your idea patented. without funding you most likely can’t mass produce it because of the cost. So the ideas are digested in a book, where everyone has access and for the poor man to get his idea out to the public he must settle to sell the patent to someone who has money to burn to mass produce it. This technique of earth changing patents eventually are to be bought by the powers to be and suppressed by the competitors so they can keep the monopoly game going and control all global energy and its production. With Free energy available to man, we would never be in suffrage and beg for handout benefits from a constituted government. Every one could be self sufficient and have no need to kidnap the power over some man’s birth right and the idea of slavery would probably end.
I am so happy that people are building on the idea of the open source arduino micro-controller. These ideas will eventually free the people from their suffrage of a manipulated greed infested fraudulent economy that our modern day Babylon is diseased and plagued by. I hope every man gets on the band wagon and lets go of their pride to bring real Free Energy to earth and to all the inhabitants.
I have been experimenting with the SSG and have a setup with 3 coils running, using a 59cm wheel with 18 magnets (neodenium). The system is working well in regards to energising old batteries,( i have a vision of using it to charge a bank of batteries to run the house) but my issue i have is that the energy radiating off the (coils i think) are causing my nervous system to tense up. I hadnt noticed it initially as i didnt realise what was happening, until i used a Gauss meter to take readings near the wheel. it sends the meter off the scale (100 milligauss) at .5m then it drops to the acceptable limit of 3 milligauss at 1m. What im finding is that long term exposure is having a detrimental affect on me. So if i could ask this question. Is it possible to shield the unit from these energies radiating from the unit? Any help in this matter would be greatly appreciated.
Hey David,
On the one hand, I’m sorry to hear that you’re suffering from EMS (Electromagnetic Sensitivity) or, the effects consequent of continued EMF exposure. On the other, it’s great that you’ve identified the corollary cause. Not many are that observant. Please do a little research on the amazing emf shielding capacity of metglas ribbon. You may find the application answer that your looking for there.
An older book entitled “The Body Electric” by Dr. Robert Becher and Gery Selden will help you understand the electromagnetic physiology aspect of it.
http://www.amazon.com/Body-Electric-Electromagnetism-Foundation-Life/dp/0688069711
Hi David, another idea might be to enclose the unit in an anti static fabric like 3M velostat. You can buy the stuff in rolls of varying thicknesses – a couple of layers might do the trick.
http://www.ideal.com.my/ideal/spec/3m_static_catalogue.pdf
checkout the 1700 series rolls, they are probably the ideal dimension
It can only happen from the ground up as these devices are merely being reestablished from their suppression. Your work really helps the average guy get a handle on how these concepts work.
Thanks!
I’ll pray for your safety, success, prosperity and peace.
Hello Mark,
I guess your right, seems to me that you are the one that brings this stuff so big and openly.
Yes experiments cost a lot of effort and money. Sometimes we don’t get the results what we really want.
Hope our plans will succeed … so we sooner or later have our own powersource even if it’s limited to our house and car.
Keep up the good work.
Paul
found you on jack bauer ts site. not enuff hours in a day eh? the reason i’m even bothering to sign your page is your willingness to give your information away.. bless you mate. when i hit the lottery, you’re on the list.
blessing to you and yours
‘loader
Hello Mark,
Nice site! Would like to thank you for the idea to use an arduino. Some time ago i also bought a freeduino ‘bare-bone board’ from modern devices.com (i now got 6 of them) and installed it for replacing the rotor (since that is a timing device only which can be done by a arduino). I also used a arduino to operate 6 relay’s that can switch battary banks from charging to C20 discharing to a rest period, while monitoring the battery voltage while in C20 discharge mode, not to get any lower then 12.4V.
Anyways to use a arduino was brought to me tnx to this site, so tnx to you! if you want to take a look at some devices check for images on http://www.crossway.nl (slow server in my house) grz from holland. Mike
ps. i put a link of the xtranormal video on a popular whistleblower website
nice!
Are you going to develop a arduino primary battery swap or charge control? That would be a interesting application.
Congratulations and keep up the good work.
I will be happy to keep in touch and share what we learn with you.
cheers,
I am also a newbe doing a lot of research in this feild, seen many websites and picked up lot of knowledge from them. I have to say yours tops them all. I am starting to build a simple one and progress from there. I’ll be watching for your wesite updates. Again a very impressive page and I’m sure many, many hours of work.
Thank You Very Much for helping some of us on our way.
Siggy.
You are going well and have done a lot of very good work here.
I am just putting together a team to seriously work in this area and thank you for your lead.
Congratulations and keep up the good work.
I will be happy to keep in touch and share what we learn with you.
cheers,
pete – au
no comment will express my appreciation of your work .
I’m a little surprised by the self motivated style of comments here… observe, tinker, learn, fail, and ultimately enjoy – but please don’t treat this page like a bandwagon you hope to get on! Doing that only increases the chances of sites like this to one day disappear. This page is a rainbow, don’t bring a dark cloud with you, here…
Thanks MAllen7424 – amazing research!
Hello Mark,
Great website!! I totally like the annimations!! Nice Work, U Rule
I Soon i hope to master the “Freeduino(Arduino)” cirquit,
(let me first read all about it)
Grz, & tnx in adv. 4 all info..
Very elaborate site. I am just researching to start on Bedini circuits. Yours is a wonderful one-stop site for all things. Thanks for sharing the knowledge.
Cheers,
Nanda.
I have only started my work with the Bedini and Bearden devices and wanted to see what others were doing. Good job. Once I get the few basic devices working great and have the time, I will let you know about larger systems I would like to build.
Hi Colin,
I hope my website helps you eccel in your quest. Good luck with your build!
–Mark
Good afternoon, great work, your right, i have never seen anyone scale up the work as you have, fantastic ! I too been slowly scaling up my work and was wondering if you can send me a clearer copy of the “3 coil monopole pulse motor/generator animated schematic”. or is it already here on this website? . . . thanks again
Hi Fernando,
The parts list are no different than any other Bedini SSG circuit, Except for your unique resistor values when you have tuned your circuit. You must understand the Bedini Motor /Energizer Circuit.
Thanks for your interest in the schematic, please keep me up-to-date on your build.
-Mark
Thanks for getting back with me Mark, Yes i understand them, i have build several, however i’m in a build now that combines all the features in these type of coils with several unique twists. One is generator coils inbeded in the main coils that when loaded, generate ac but “REDUCE” loading on the main rotor, cause it to speed up and lower the AMP draw !. keep you posted . . .
How are you Mark, wondering if you can help me? can you recomend an inexpensive “solid state relay” that can handle about 2-3Amps and about 100v max .. .TKS
Sorry took so Long Fernando, I am so pre-occupied with the home front and catching up and preparing for the change of seasons, but I did a quick look around to try to help you. Look at this link:
http://www.mouser.com/catalog/629/1435.pdf
-Mark
I agreat a lot work because i am building too, one (Adams concept) to be powered by a solar panel. (I am designing a very specail e- solar powered bike. I have problems with the coil´s driver ; i use 48v but no way to find a good shematic´s. Iñ´ve got J.P. Naudin Adams design but no work. I need some help to design a good driver ( complete with a parallax or similar and connected and managed by a computer. May vbe you can give a help with it. May be i can use your shemnatic´s to charge mi A123 by pulses better than with a collecting coils. Bravo for your job and help to the motor pulses comunity, keep going on thanks
Hello and many thanks for your HUGE efforts in this arena. I have been researching renewable energy for some time, reading most of the links on the web / youtube. Which eventually led me to your website. WOW!!! so much work and you are sharing the research with all…..Thank you so much. I won’t get political or religious here but if more people do the same, the whole world over; then the governments, big companies may just get undermined and the ‘ordinary’man just might be in a position to take control of our own lives and have a better future. I work with people in the squatter camps in South Africa….we so NEED cheaper electricity soooooo bad…hence my research. If I win the lottery you will get a huge donation from me…..keep up your excellent work. Kindest regards, Paul.
Great job
Just wanted to say thanks for the information found here, you have put some time and effert into this. I am working on getting my window motor running on the arduino, just add another circuit and work it backwards. I will be starting with your code and work from there, I have some ideas, just need to learn the codeing. Thanks again. Peace Rawbush
Re: Great job
My arduino code is strictly written for a SSG circuit with the diischarge circuit 1:1 ratio, you must under stand how the electronic circuit works mechanically to understand how to manipulate the electronic circuit with software code. I basically know the SSG circuit and the pulse circuit very well and from there I written in Arduino code (C++) what the circuit does in software code form which mimmicks the mechanical trigger embedding in the code with the options to manipulate with code the additional variables of distance of magnet from coil and how long the switch will be open(amperes) to charge the coil to zero out the magnetic field from the passing magnet. If you dont build it the exact how i printed it the variables must be changed to tune the circuit. Be sure to moniotor the temperature of the transistor running the motor until you have a range that keeps it at room temperature. It is very simple in my eyes. Any Questions I will try my best to help!
The ‘Law’
When I was 10 I asked my parents why we didn’t make our own electricity. They replied we didn’t have, PG&E did it for us. Towhich I replied; ” Doesn’t that cost money?”. Long story short, I was forcedinto silence on the subject or face further punishment! Today I know the ‘Laws’ aren’t worth the paper upon which they are written! The ‘Greed’ and the ‘Addiction’ just make sure we never know the truth. Well….. “TOO LATE!” Today I’m 54 and now that ‘Oil’ has a black eye, I say we ‘kick’em when they’re down!’
Building my own. And building Bedini!
You are not alone, I am building the SSG with the trifilar modification, I have two really nice bicycle wheels and I want one for my job and one for home! I am scaling a motor that uses timing and displacement to create not just the radiant reclamation, but to also serve as a motor to spin a home generator. The Arduino Idea REALLY intriques me! How do I get more information? Please! Thank you!
Re: Building my own. And building Bedini!
Thank you, I wish you luck with your build… As far as I know, I am the only one with a working bedini motor running on an Arduino. You will not find any more information on the subject except for what I post on this page. Everything you need to build one is printed here. Good luck.
Getting up to speed
Just saying hi, your self description reads like I might write one. To sum up I just encountered alternative energy ideas Jan of 2010 started with the perendev/steron/searl/ and now have been looking at Deyo/Bearden/Bedini/Moray/Tesla(of course) and now yourself, and others. At this point I am just hoping to have some dialogue with someone wbleepeddoesn’t think (whatever goes through their heads) I’ve lost my mind.
datos de trabajo con bobinas con regulador integrado
mallen7424 estoy arrmando y he provado con varias bobinas de diferentes calibbres de alambre y observado que hay bobinas que responden mejor la primera que hice la hicimos con 600gramos de alambre no 22 y 600gramos de alambre no 24 enrrollado juntos dando las siguientes datos el de no 22 nos da 54hms y el de no 24 nos da 30hms ok esta bobina la acomodamos a un disco con un motor pequeño con 4 imanes de 2pulgadas de largo con 6mm de ancbleeped por 5 mm de grosor da un proedio de 80rpm es decir muy bajo pero al cambiarle de polaridad 2 imanes a sur quedando 2 n- 2-s trabaja muncbleepedmas rapido es decir a unos 1000 revoluciones pero las bobinas que hicimos para hacer uno ya grande de 1kilo gramo de cada alambre del 23 y 27 con los siguientes datos el de no 23 da60 ohms y el de y el de no 27 da 260homs pero este lo pongo de la misma forma a los imanes y trabaja muy despacio hemos mando hacer 2 cilindros para los imanes de 1 llavara 12 imanes de 3pulgadas de largo con 1/2 de grosor y 1/2 de neodimio grado 42 en un cilindro de 6″ de grosor para ponerle 1-n-1-s-1-n-1-s- y el otro de 2″ de alto con 6″ de gosor este llavara 16 imanes de los mencionados anteriormente tratamos de generar lo suficiente para cargar 2 baterias mas arrastre un motor mediano en ca de lo que hacemos nosotros el tema es si no funciona de una trabajara de otra modificando sobre la marcha ya que el cilindro de 3 pulgadas movera al de 2 pulgadas con libertad sin tocar las bobinas esclavas que alimentan las baterias tengo varias confuciones sobre las bobinas que den buen rendimiento tu estas ya adelantado algunos años en esto que nos aconsejas vamos bien o nos regresamos espero tus consejos y ya subiremos los videos sobre estos trabajos saludos
me encanta su trabajo muy buen dato
estoy en mis primeros pasos he hechos 2 como prinicpiante y he acavado de terminar el que quiero trabajar ya en forma clave con los flotadores de carga para 2 baterias como lo tienen aqui ustedes hay unas preguntas que me gustaria hacerles he ecbleeped 2 ruedas con 4 imanes de en base de motor lector todos norte y trabajan muy bien la bobina da 54homs la de no 23 y la del no 26 da 30homs de restencia trabaja muy bien su peso es de 1.200kg. en el carrete juntos pero haciendo pruevas le invierto 2 imanes polos opuestos lo cual trabaja mas rapido incluso se oye el osilador cuando esta el polo opuesto es solo pruevas pero ya ise 2 cilindros de aluminio masizo de 6″ con 6 imanes de 1/2 de grosor x 3pulgadas de largo quiero hacerlo con imanes n-s-n-asi genera muy buen volatje parejo a este cilindro que me consejan cuanto le puedo poner de osilador y de esclavos para que tenga suficiente fuerza para mover cosas grandes como motores de 2 o 4hp el cargador de baterias que tinen el timer 555 a cuanto carga a otra cosa que observe es los voltajes de operacion y de trabajo que no tine el diagrama de 2d lo nesecito para sever cuanto puedo cargar 2 baterias libres y alimentar la de trabajo si hay alguin que me lo explique se los agradecere saludos y muy buen trabajo
feleicitaciones por ese trabajo
seguimos sus pasos en varios experimentos sobre sus generadores esperemos tener algo sustenable para aforontar los huracanes en la peninsula de yucatan un saludo desde cancun mexico caribe mexicano
Going beyond Bedini
It is excellent you have published the 3 coil monopulse using a non-battery load. I suggest you program your micro-controller arduino in order to command igbt or mosfet drivers which will replace reed switch and third coil sensing so you’ll tune deeper your device. In other words, the software will generate the signals going into 2N3055 base & SCR gate.
Re: Going beyond Bedini
I have that configuration all thought out, except it will be an upgrade for my 12 coil for experimentation.
nice site
This is a link to a book I have on my website from the head of the German space energy research centre look on page 368 of the PDF reader and you will see why zero point tuning coils are suppressed. I am sure you will enjoy it. http://www.themeasuringsystemofthegods.com/Meyl%20-%20Scalar%20Waves%20%28first%20Tesla%20physics.pdf
Size of coils
With the magnets used in your examples: Is the complete spool of coil being used. i.e is the magnetism reaching clear to the outside of the coil?
Re: Size of coils
Hi Ken, I am not sure exactly what information you are looking for, but I believe you are asking me if the ‘Magnet Width’ is covering the ‘Coil Diameter’ and if that is the answer you are looking for I would have to say, “Yes the magnet width is 3/8 of an inch larger than the Diameter of the coil”.
book
which of the Bearden/Bedini books do you suggest I get to start this out.
Thanks
eu estou engatinhando nos meus esperimento ainda, mas estou na luta.
por uma energia limpa e livre.
não sou nenhum expert.
Abraços Edgard.
size factors
I have just started in my experimentation of the Free Energy world. My goal is to build up to charging 6KW worth of batteries a day!
With the latest prototype you have shown on this web site, what is the size/number of 12V/6V batteries you can charge. I do not mind if I have to make several of these types of motor/chargers, but I would like an idea of what I am up against.
Also, are you heatsinking any of your parts?
Any comments or ideas would be helpful.
Re: size factors
Hi Ken,
In my experience and experiments I do believe you can charge any size bank of batteries from 1.5volts – 18volts. I run my setup and experiments with 6 -12volt batteries, I believe I can go up to 24volt but I am not sure because I dont want to take a chance to blow any components because of lack of funds. Only thing I can say is to keep you building is that you will be able with no problem charge your batteries, but my power factor data of input vs output because of lack of funds in my most recent experiments have not been controlled experiments to get accurate numbers to give the actual COP.
I do not use any heat sinks in my setup except on my discharge circuit of the capacitors, which I dont think I needed. Everything stays room temperature! One day when I get brave I will run my machine at 24volts and measure the temperatures. Hope this helps you.
Thanks for coming in to my website…stay tuned!
THE UNIVERSITY OF THE ABSOLUTE
306 North Brooks Street
Room 409
Madison, Wisconsin 53715
ATTENTION; To whom it may concern,
When I first got to Porch Light Properties, I thought they would really be of an help, but little did I now that Porch Light would turn into a problem.
I live in Madison, Wisconsin. The people here are a great deal of trouble, they black mail persons, extort money from persons lead to believe that they are helping the home-less, but the opposite is true. They merely extort and use the people that come to this place for real help and Porch light Properties is a sham what refuses to be of an real help and support to persons like myself. Porch Light Properties gets money from the government to house and feed people only, but I can’t even get the help for Porch Light what I need to help me of my business and business interests made of a success. And Porch light Properties is a kind of the government sucking thing getting money from the government to further derelict persons. I am desiring to get away from this bunch killers, and that is my need for that is what they are.
But I am writing, to you, in need of your help. I have a research and development corporation filed in the state of Wisconsin what I have been trying to make of a success, and I am working on FREE ENERGY types of the things. I have asked people here to work with me, they are disinterested and they suck…that is how I think they make their living. However, I am interested in doing something constructive with my life what remains when very much interested in the furthering my research development business.
I am a writer who has developed, already, the many of the very advanced ideas and I am in the continued interest of my developments of my mathematical theorie of the TESSERACT and other related forms of the mathematiques when completely developed what I think can be used to explain the physical phenomenon of the world when making of an use of a different kind of a means that means different then the relative and the quantum mechanical.
And I am interested in the continuance of the development to my technologically related form of my ideas what have to do with a new kind of the mathemetiques what I have developed. Another one of my developments is that one of technological means of the instantaneous transport, time travel and the other of the forms of the science and technologies what have to do with the use of light used to precipitate solid material objects directly from light.
But the trouble remains here, persons are un-friendly and fierce, insincere, un-helpful and troublesome and most persons around me here are totally un-motivated to contribute to society and the persons what surround me are not at all progressive persons, but rather they are not trust-worth persons who are criminally minded and they have no respect for me but they harbor contempt and dis-like persons who have different ideas then theirs when their life is about doing criminal things and my life is to do of a different and of a contribution’s means.
You can read as related to my ideas having to do with what I think are the stars what I think are globally lighted and powered made light and electromagnetiically emissive made so of an use of an industrially related means lighted and powered of an use of a wholly new and different kind of the industrial operation what I think, similarly can be used on planet by the the American Republique using the Teslian related form of the technology used industrially on this planet so to electrically and industrially light and power planet earth, similarly, lighted and powered of an sue of an industrially related electrical means. You can read as related to my industrially related ideas by going to one of my web-sites what treats on one of the directions had of my research and development corporation.
http://www.onthelightoftheworld.com
The problem is that people here in Madison, they are abusers, usurpers, killer and thugs and I am needful to move away from this community what is full of skeptics and persons who refuse dialogues and will not take interest in the any one of the things of my genuine curiosity and interest. Thy think FREE ENERGY kinds of the related things, a sham. They fail to realize the reality of PERPETUAL MOTIN a very relating what yet requires the greater amount of the research and development work what yet is needed of he phenomenalism.
When the non-support here is that sufficient to allow me of a the need to escape from this bunch of killers, userpers and liars, I know this is a bad report what I am giving you about my neighbors what are hateful, fierce, un-kind, mean, stupid, un-educatable and lazy but never-the-less the content of my sayings be true. It is true and I am needful to get away from these people types when having been forced to live here before I am very poor financially. What I have told you is the truth of the circumstance but it is the truth necessary to tell and I am saying, to you, the way the situation really is.
The persons here where I live…they are mockers, doubters and skeptics and they think FREE ENERGY stuff a fraud, but I do not think so! I am no longer interested in dealing with dull threatening and stupid people who will not believe me nor bother to find out and they ruin me of jokes, un-pleasantness un-concern, dis-respect, selfish dis-interest dis-regard and ridicule. In my un-happiness and great concern for my actually safety and life, then I am constrained to make provision to actually move.
I live in Porch-light Properties in Madison, Wisconsin and have asked them of their help and concern, but they tell me that my request, of them, when needfully their help is out-side of the elements of the MISSION STATEMENT had of Porch Light Properties. When the Porch Light persons are not that helpful when not willing to go by the rules where I live, on this account then I am constrained to move away from the dis-order of the environment where I live, and in this way I am writing to you because of your like interests in FREE ENERGY types of the devices, interests and systems.
I am seventy year of age and I am a single male. I am wishing to move from this environment because of a lack of emotional and of a lack of supportive common interests and I am completely fed-up with the mis-crient persons around me who steal clocks from the publique kitchen, and to me, the all of this behavior on the part of these morons who refuse to go by the rules…my own opinion is that am finished with putting up with the Porch Light authorities who are acting in collusion with the Madison Police to ruin me. The Porch Light persons are in sympathy with Madison Police who, in fact, like the persons in my domicile are, in fact, noting more then a bunch of stupid lazy law-breaking thugs who are completely irresponsible, selfish, mean and completely worthless when beyond of an interest in being redeemed.
Porch Light has indicated, to me, that they are not wiling to enforce the rules where I live and this is another motivating factor what constrains of my decision to move. It is frightening, to me, where I live when having to be around these fierce kinds thugs where things can not be discussed who are ruining my life all so bad .
As long as I am of the opinion to move, in light of my interest, then I am thinking that I should move to to Worcester, Massachusetts because there are persons in Worcester, Massachusetts who have similar interests to my self, and since it is of your similar interest then I am writing, to you, explaining, to you, my situation. and I am writing, to you, so to gain of your understanding, support and help when exceedingly interested in relocation . As I have already indicated, I am interested in relocation because I am no longer willing to live with persons with no sensitivity to myself when the thugs around me are dis-interested in any-thing what I have to say and when the freaks around me refuse to contribute, understand nor help me of my need when support in my interest is that what is required.
In that continuance…I am writing, to you, needful to find out, from you, of your willingness and of your interest in my being an help, to me, to relocate and as related to you persons in Worcester if, at all, you would be wiling to help of a person such as myself of whom it would be that would be-friend to a friend, with an mutuality of an interest what also would be of a benefit, to you, that you would be of an help, to me, in my exercise of an re-location as we could be of an mutuality of an help one to the other.
If you would be empathetique to my plight would you please provide me with names, addresses, telephone numbers and E-mail addresses of persons that I could work with and of the names, telephone numbers and E-male addresses of person who wold be of an help, to me, in my situation. I would appreciate it ever so much. And that I would like, similarly, to find out as related to the kinds of the accommodations exist where you are as could be offered t a new-comer and I would, similarly, like to find out,from you, as t the nature of the projects what they are being worked on by others also?
The loneliness what experience here with these persons also up-bearable. I am in the need of finding out about of a re-locate to an area of the country where I would be appreciated for my talents, education, knowledge, training and interest and I could help when living in Worcester. One thing more…I do not have that much money but housing accommodations made with persons of similar interest would be well appreciated and we can work together so to stregenthen one another interests and research
And my telephone number is this one. and if it would be that would like to converse, with me, I am available for telephone conversation and any time that you should like to call, I will be here to receive you.
In the closing the more as related t m discoveries; I do not believe the stellar radiant bodies, including the sun, hot bodies. They seem hot to the distant observer but under the barrier of the heat what they exhibit at some distance away from the stellar radiant bodies, they are cold bodies what are very advanced civilizations.. The stellar radiant bodies, all, are very advanced cosmological civilizations lighted and powered of an use of the industrially related means as first discovered and demonstrated on this planet by Dr. Nikola Tesla, and my opinion is this planet earth also that one possible to light and power industrially and electrically, like the stars.
In the interim you can read the content of one my corporation’s web-sites having the URL what tis:
http://www.onthelightoftheworld.com
Thank you, and if you were to respond as quickly as possible as it is that I am eager to complete of the making of the the necessary plans of the re-vocation…I would like to accelerate of my related form of the arrangements completed to move to Worcester, Massachusetts, and would like to do this because that is the business community where the FREE ENERGY people have elected to congregational to perform.
Write soon…
William H. Millard
THE UNIVERSITY OF THE ABSOLUTE
William H. Millard
wmillard@earthlink.net
POWER DFYNE TECHNOLOGIES, LIMITED
Post script:
When younger, I worked very hard so to be able to qualify to receive Social Security benefits.
In that receipt of Social Security benefits; have used the money what I have received from Social Security to help my-self and to do something for others what is of an extreme importance, and in this way alluded, I have discovered that persons will not further assist me of my honest desire to get free from this ENTITLEMENT.
I think some of the reasons this kind of the negative stuff occurs in my life is because persons are angry with me because I am a Social Security recipient getting a pension from the government, and they do not like that. But my exploiters, similarly, get money from the government also but they will not help me of my serious attempts at being financially successful with my business, and the crooks around me are not using their money what they get from the government used to do anything to help any-one, at all. I would gladly give up this Social Security thing if it would be that I had help to develop o my business related interests what would give me a monetary income what honestly I have tried to do.
When I came back from California, I made the mis-take of borrowing money from predator lenders to launch, on-line, my business, and when I could not pay back the loan then my business became of the failure. My on-line business interests, then the more of the trouble, and am yet making of an effort to pay off the debts.
Small machine shop to help make parts here…
Hi everybody out there in the independent energy research world!
Unfortunately, I can’t simply give away either materials or time,
but if people either wanted to have parts made [for lack of other help
from other sources closer by] or even partnership up on projects, I
would be willing to talk to you, as we here are seeking ways to
eliminate the energy monopoly that has put us so far behind as a nation
and polluted this whole world with smog and toxic wastes of many
different forms.
So long as we can afford to continue to operate, we want to help as inexpensively as we possibly can and still keep the rent paid. One major advantage for us if these designs work, is that since all of our equipment runs on electricity, we could completely eliminate our electricity bill and that would save up a ton in operating costs!
Solid Work
Working through the circuits myself started with simple SSG… have arrived at the “monopole ne555 capacitor dump” motor now. The Kromrey generator is next as I feel this has the most potential. Easy to build, understand and I think usability.
All one should be looking for is a collapsing magnetic field in a coil. That is where energy can be tapped and collected….. seemingly free.
One idea could be to Use One battery as primary and a capacitor bank to charge. Switching off motor, dump cap charge into battery (while disconnecting from primary side), run motor etc… and with this drive the kromrey generator.
Peace.
Re: Solid Work
Very well said Lars!
Swapping of source and charging batteries
Dear MAllen7424,
Thank you for such usefull information, it was so interesting to have a look on shown models and animated diagrams. It’s a good job, hope most of readers feel the same.
I’m interested with Bedini technology for a few years and already have made a few types of Bedini motors , but can’t allow no one of them to selfrun or keep it running by replacing source battery with charged one and back. Do you have any ideas concerning that ?
Also, please , could you send me the drawings of 3 coil monopole motor/generator ? I’d like to build it and test. Thanks in advance for any reply,
wish you success in your very important work.
Kirill.
Re: Swapping of source and charging batteries
Hi Kirill,
The information you need is in this website. If you have built the Bedini SSG or any other advanced machines then you already have the knowledge to build my 3 coil Generator, my schematic will only be a guide, your geometry and coils will be different than mine, but dont worry, tuning you already should know. My generator is just like Bedini’s patent ‘Radiant Energy Energizer’ except with a twist. My schematic is just his patent x3 with mechanical reed switch discharging instead of 555 timer in a 3 phase discharging sequence and upon load it speeds up with limitations. There is nothing complicated about building it and nothing you don’t already know or have access to for designing your own version.
I dont have any self running examples to help your concerns. Thank you for your comment and good luck with your builds. Self running is not my goal here, just the battery charging and creating light with the HV pulse and as you can see I am successful at that. I hope my website will help you move forward in the world of Radiant Energy.
Mark
Capacitors in this circuit
Hi i just wanted to say the animation is great here, I recently ordered the parts to build me one, I currently have a SSG working an it works well I found this an would like to try it out but when me the parts guy got to the caps he asked what type, metal can type? or many others i didn’t know what to say i’m (newb) so my question is 1uf 600v an 10uf 600v is it metal can type or one of the others also are these VDC rated.
Thanks in advance
Hi,
I’m very interesting about your work.
Sincerely.
Edmundas,Lithuania
I want to build one!
I am going to build a motor folowing your schematic ’4 Coil Monopole Motor setup with 4 master coils’ and am wanting to confirm that your one makes power
Re: I want to build one!
If you have never built John Bedini’s SSG circuit, then I do not recommend you build any advanced motors. Please save yourself money and time and study his circuit and referenced material before building multiple coil motors/energizers.
Plan.
I’m very greatful to you for everyting your doing, i’m trying to build one my own, however ihavent got a plan.
could you email me a plan for the parts and wires?
Thanks in advance
your motor
I am not sure how to save this stuff on my computer so I can view it again.I would very much be interested in viewing it again .Will you email me this page. Thanks and God Bless you for what you are doing.
Jean
capacitors in this circuit
The animation is way cool but I couldn’t read the text to figure out part numbers and that switch? Any help would be apreciated.
Thanks
Dale
I have a SSG running right now so I’m ready to try a three coil machine.
Re: 3-coil Monopole Pluse Motor
Hi Dale,
All the part numbers are the same as the one on my Animation of Bedini’s patent. The spinning switch is 3 reed switches in a certain configuration for sequential discharging, you can use any type of switch, but be sure the timing is exactly the same as you see it to trigger on the discharge end. If you know a bedini Pulse Charger Circuit then you should already know what parts are needed. Nothing out of the ordinary. I just created a 3 phase system out of his patent.
3-coil Monopole Pulse Motor
Hi
U have a good idea, but I think maybe u are making a mistake, see that u have the magnets just in one side of the coils, if u put another 4 magnets with south pole on the outside of the coils and unit then with iron plates u will get more radiant power maybe.
This is the way transformers work with iron laminated cores that makes a closed magnetic flux, hope u understand. I wonder if it works.
1uf cap
Hi
I have the original circuit that come with the Bedini s book, I want to know if the 1uf capacitors needs to be 600V or not? why?
In the original circuit only the 10uf capacitor is rated at 600V.
Hairpin circuit
Hi from Costa Rica and Thanks for all the aclaration infos.
Did u ever see the Tesla Hairpin circuits where u can make radiant energy (a lot of it) and light bulbs with it.
see http://www.transformacomm.com
so I want to try charging batteries instead to light bulbs, maybe it is a more efficient way to do it (and easier).
Ok the trafo consumes not less than 2A @120V AC BUT maybe the batteries will charge very fast and u can archieve better results in less time, so what u think?
Re: Hairpin circuit
Sorry for the sumption on the current draw, thats the nominal data of the transformer about 2A @ 120V AC, I have no test it with the Hairpin circuit yet, so I dont know how much current it will draw from the wall outlet when the radiant appears. I hope it will be only a few milliampers and the batteries charges super fast (maybe too fast??), it is my opinion at this time only. Im waiting for the capacitors that I buy en Ebay from Ukraine.
Basic Readings
I just wondered why you don’t include basic readings like voltage/current in vs voltage/current out with different loads.
Re: Basic Readings
I do have some basic readings on my youtube page http://www.youtube.com/user/MAllen7424 during some of the build. My setup changes extremely everytime I work on my project that changes everything. If I spent all my time taking voltage readings and experimenting in every stage of the build, I would never finish my idea on the bench. I dont mean to not advertise all the information everyone wants to see, I am alone in the R & D of my lab experiment, I do want to experiment and log all data for everyone, but it is time consuming and I am anxious to get it finished. Until that moment comes everyone must please be patient with me. I am very close to finishing, until that time comes then I will take the time and concentrate on logging and record data for everyone to see. I am a one man team with no time to spare. This winter I plan to have it finished for everyone to see. Thanks for your comment John
Mark
Over Unity
Sounds far fetched and crazy, …”
Actually to someone who has had a long career in industrial power control design it just sounds sadly ignorant and self-deceptive.
“Show that it’s wrong”. No, extraordinary claims require extraordinary proof, and over *unity claims* are as extraordiary as they come and require very clear evidence. You have to demonstrate your flying sheep. I don’t have to throw a flock over a cliff to prove the common understanding that they can’t.
There are *simple* and *direct* methods of measuring the energy flow to/from the battery but your speadsheets seem to use a convoluted (and highly unreliable) method based on battery state-of-charge when a wattmeter would produce very clear (and under unity) results.
Why choose to measure such an important parameter in such an indirect and unreliable way, particularly when your results flatly contradict a large body of very well established physics? You know that “Over Unity” is a radical claim, but perhaps you don’t see just how radical – to prove this you have to un-prove just about everything else, starting with the Laws of Thermodynamics. Good luck with that.
If what you claim is true (COP<1) then it should be a very easy matter to demonstrate that the nett current is flowing TO the battery. You haven't, and to me it looks like you simply have a systematic conceptual error.
Consider this; conventional (under unity) devices run down because they dissipate the original energy as waste heat (eddy currents, I-squared-R, friction). Now if we happen to have a device that is neg-entropic (over unity) it will be gaining energy from the surroundings. So once started what is to prevent this unstable situation running away with catastrophic results? After all it would have *negative* losses, the faster it ran the more energy it would aquire – Ka-boom!
Re: Over Unity
Wow–you have stimulated a very important thought to me–an negative entropic system might continuously collect energy until boom. I’d never really thought about that. The reverse, however, is never true. Just because a car is full of 20 gallons of gasoline with tons of kilojouls of energy does not mean the continous energy release explodes the engine. If a a machine has a fixed efficiency of say 110% and the energy is charging a battery, it will not go boom, it will merely charge the battery at the 10% rate (whatever VA that is.) I now tend to think of it in terms of efficiency, and that prevents me from going boom. Whew…
electronics
Hi! It’s me, Idaho. I’ll have to spend some time looking this over. I have researched a lot of this sort of material but haven’t done much as far as building in the last few years. I’d like to help out and I’ll try not to get in the way.
Have you ever run into Bill Lyne in New Mexico? He has a fasinating device, I’ll see if I can find it and send it on.
I also have a cd of Thomas Jefferson Jackson See’s material. He was a friend of Tesla and a brilliant astronomer and math whiz. I’ve had lots of math and he loses me fast(like everyone should know what the 7th derivative represents?). Still great stuff on aether theory.
I am also interested in Stan Meyers work and I have a friend that knows Dennis Lee.
Glenn
Bedini 10 coil motor charger
Hi Mark!
I’m very impressed with your 12 coil motor charger. You have done an excellent job. I really appreciate you sharing your experiences and testing results. It is an inspiration for all of us.
I have started building my own Bedini motor. I’m building the infrastructure to support a 6 coil motor. As this is my first, I will start with 1 coil and run tests. Afterwards, I will expand to 6 if the first looks promising.
Mark, I must admit that I am having trouble finding information on the internet to support utilizing larger Bedini motors for practical purposes / home power generation. Bedini’s 10 coil motor is stated to produce 10 KW of power.
Are you seeing any promising output power that can support Bedini’s claims to 10KW from a 10 coil system? Yours is largest system I have been able to find on the internet and is the only that I can find for such comparisons. Do you see any evidence that a 10-12 coild system could power a house with a large number of batteries being charged?
Any advice you can offer would be greatly appreciated. Please feel free to email be directly. I would be happy to share my test results as I go along.
Thanks again for your openess in sharing.
Preston Stroud
Re: Bedini 10 coil motor charge
Hi Preston,
Thank you for your comments on my 12 coil motor/generator. I know of all your troubles out on the internet are filled with chaotic misimforming information, this is the reason I have started this web site to follow my progress in my understanding of the technology.
Only thing I can prove is the there is something there and the bedini ssg circuit is the basic setup to understand this radiant energy that Tesla and others had discovered. Only way you will understand it is study it by building it and understand John Bedini’s ideas and of course Tom Bearden’s books on energy from the vacuum and other theories that go along with it.
My project is an experiment using the circuit for experienting with this captured potential in a pulsed system for which I have made. The geometry of my project is far smaller in scale than Johns version, where I would not get that much power, even if I knew exactly how he built his, my project has small coils in the system which I am sure differs in the potential power manifested in both our motor/generators’. I see potential that is definately there to harness, but I regret to tell you that I have not been to any level of John’s claims only for the reasons that I am building my own design as far as the geometry which is based on his circuit experimenting and it is a slow process alone building and experimenting at my own leisure. I have yet experimented in the negative entropy theories of his circuit to give you the answer you are looking for, that I apologize.
Don’t get discouraged, all I can say is that you are on the right track. The technology is there and always has been there. You just need to open your mind to access it! …and build it! Advice I marked in red text in my page some recommendations to get started . Hopefully the rest of the reading will help.
Once again Thank you!
I didn’t mention on site that I was away from my project for a brief amount of time…so stay tuned!
Hi,
I’m very greatful to everybody who is trying to save our world and I will try and contribute as much as I can.
I need
simple project of Bedini motor , exactly dimension for everyting parts . ioji.tibiscus@yahoo.com
max consistent COP achieved?
Hi,
i am intesively involved in Bedini technology last months but did not achieved Overunity in any way. Seeing your advanced setups as stated in the infamous patent, I ask you and i please want to hear a straight answer.
What the best COP you achieved consistently so far? I need to know, please.
Regards,
Baroutologos
Re: max consistent COP achieved?
With all do respect!…We all would like to know the straight truth and to achieve overunity. My project is driven by the ssg circuit. Everything else is designed by myself for other reasons to gain knowledge. I did have some test data runs. But obviously you are looking for einstant satisfaction without doing the reasearch and reading. Otherwise you would have found some early test results on this page. Science and technology didn’t build the space shuttle based on what that one inventer told them it was going to do and how it worked, it took R & D. Once again I am not looking to build the ‘machine of the century’. I am building this to gain knowledge in these fields of Electrical Engineering(EE). Sorry if you are debating with yourself in deciding if you are going to build one or not based on someone elses data that could be inacurate.
The only reason people build the SSG is to learn its concept. Your imagination will take over from there. What is so wrong about learning something. If you dont want to learn on your own. Dont build one. Go to Bedini’s site and buy an already-built charger. Believe me I would answer your question, but I am by myself on this build and I only built 1/4th of the machine planned. Its not finished in other words. When I get to the point where it is finished and the machine is consistant without changes then I will take data down to satisfy everyone. I can’t give you accurate data on a machine that changes weekly from my upgrades. Anyways don’t take it personal. I would like to display the data everyone wants to see because I can’t get this thing built fast enough. Research & Development takes time and money and usually more than one person on the same project. You can come waste weeks taking data but I will push you away because I am going to upgrade my ideas on ‘my unique project’ which will change the data results each time. To me it is not COP>1.0 that I am looking for, it is the knowledge it is going to give me to advance the ideas. My motor may be running on the SSG circuit but one thing I am not looking for is overunity. I am looking for knowledge that our education system somehow took away from us. My grandfather knew how to build a motor/generator when he was in grammer school. And I at 37 had to learn from others including John Bedini & Tom Bearden and many other knowledge seeking people on the internet. Only thing that education taught me was to be on time and play the game by their rules only…or you will fail!
My Motor/Generator Experiment Lab is not an SSG. It is driven by the SSG circuit respectively and it is once again only a test lab machine of multiple ssg circuits that happens to be the drive circuit I chose in teaching myself about Motors/Generators, Radiant Energy… An All-In-One Test Lab. I am not looking for COP>1.0 I am simply looking for knowledge. If I achieve over unity or COP>1.0 then great!… at this point I am not concerned of free energy. If I achieve it then my readers and the people that are watching me will know as soon as I know. I am just sharing my researched knowledge and sharing my progress on my Motor/Generator.
Everyone building the one coil bedini circuit has it easy!… try messing with 12 or more circuits with multiple triggering sequences and multiple discharging sequences, you will understand what I am going through. I have questions and a whole mess load of them. It is very easy to get mis-lead on false information. I just went to the extreme because the project wouldn’t have been challenging enough to only build one coil system. Everyone is building that, why not build 144 coil system… I bet you can find multiple branches of ideas just because of the scale of the system with a variety of different results and different possible applications that go along with its unique geometry.
Re:Re: max consistent COP achieved?
Sorry if I offended you in anyway..
Thanks for the prompt reply sir. I assure you not many people involved in OU projects are willing to share their experience in pursue of overunity.
Ok i understand that you are NOT after achieving C.O.P. over 1 in electrical terms and did not meant to upset you or distract you from your studies.
Personally, i am attracted to bedini technology (as most people do) because he claims that achieving OU is a relatively easy task. (although most people i know involved have miserably failed.)
for me proving my self that i could “generate energy” from vaccum etc will be a turning point in my life. I think you understand the implications. Last, there are is a saying that goes as “believe or not, do the research”. I am researching! I stick to the rules blindly. I try without success till today.
On the other hand, i do not want to be a cult member that is ghosted by the OU dream that actually have not ever experienced.
Anyway, you need not to replay this. Finally from a backyarder reasearcher point of view, i feel an urge to congratulate you for your great mechanical skills and considerable effort presented in this site.
Regards,
Baroutologos
Great instruction on muti coils, your contribution is priceless
Hello MAllen:
I have seen 1000′s videos.
Yours in one of the top vid on youtube.
Because, multi coil motor is what we are looking for power and torque that really can change how we use energy through out the world.
Your name will be remembered by 1000′s, Thedaftman,Lidmotor, Hohnydavpro and you ! That really make differance.
Free energy is on our way.
Your detail guiding instruction will help us all.
Thank you and sincerly
Ed
Re: Great instruction on muti coils, your contribution is priceless
Thank you Ed,
I dont think mine is at the top, but I appreciate the gesture! There are many great inventors and tinkerer’s out there to see. They all are great for sharing and expanding our knowledge in the search for the ultimate creative moment in our lives. You are right, we do need to create a better sustainable life here on earth away from the war-mongers, Free Energy would be that change needed. I hope someone is fast in getting us there honestly, for the love of humanity. I am trying!… thats all I can say in my contribution.
Great animation…
Hello MAllen7424,
I am impressed with your animation. I will look forward to your future experiments. Your list of materials is also excellent for building and reproving purposes. Most sceptics say the power is coming from the batteries. When will it be a self running power generator with out batteries?
Re: Great animation
Thank you for your comment. I have spent alot of time deciphering the crap on the internet and I have compiled the information that I found to lead myself up to get me building. I have posted this information to help people get started quicker so they dont spend a year researching before building one like I did.
I believe, but do not quote me on this because I am NOT an Electrical Engineer or physicist, that the energy comes from everywhere in the circuit …from the callapse of the magnetic field , to the spark of the transistor (splitting the positives) and even in the diodes and resistors. I believe the correct term in my reading is “Negative Entropy” is the source.
The battery?… I dunno could be just and antennae that needs to be tuned to the receiver like a Ham Radio operator will use an SWR meter to tune his antannae to his radio gear consisting of variable capacitors and trimming length of wire to get the tuned wave length. I believe all these variables come in play here. Which lead to very difficult tuning procedures. In my 12 pole my circuits all have the the exact same length of wire everywhere because technically I have 12 seperate bedini circuits in my configuration. And knowing a bit of Ham radio. I built based on keeping the length of wire consitant in length through the circuits for the end result to adjust only one length of wire coming out of the collectors or from Magnetic Coupling of coils (induction) to be a bit controlled for tuning in the final testing and experimenting.
My 12 pole monopole motor I have built is not in my goal to create free energy, but to learn for myself because Electrical Engineering in my generation of education was not an option for me. So I took the liberty to build this unit to teach myself about electric motors, generators, Alternators and configuration thereof (Delta,Wye) and also this Radiant Energy. In the process I have taught myself basic electronics and used my mechanical drafting skills and IT Technician knowledge to build an experiment machine that is flexible for all these experiments in these fields of science and physics.
I practically live out of a suitcase and dont have a permanent lab or workshop. My workspace consists of a 1 square yard of table space. So instead of building multiple motors and generators and prototype experiment models that I dont have no working or storage space for, I have engineered this one machine that fits in my small work space to help teach myself about all these fields of Electrical Engineeering and physics behind it.
I will be seperated from my experiments for a couple of months. In the meantime I will be gathering research and doing my best to help the people of the world understand this as I learn it for myself. Again…I don’t claim anything here. It is just research for humanity. People will classify me but I dont care! I know my mind is concious and powerful. I just hope I have helped people to open their minds a bit more quickly. The mass confusion of information on the internet with all the debunkers and deniers falsifying information out there only to convince people to not think for themselves. Even if I never create this “free energy” In my experiments by trial and error with this machine I have over come ‘Lenz Law’ by bypassing the effect. If thats not progress and inspirational I dunno what is!….. Keep thinking for yourself and never trust the Mass-Media!
Mark
Oh, I almost forgot to mention: not only has anyone seemingly bothered to connect a wattmeter to the battery that, is it claimed, is only used “initially,” but everyone also seems to have forgotten that various integrated circuits within the system incorporate active components that draw yet more power via VCC (BJT technology) / VDD (MOSFET technology). Someone really must teach this John fellow about the very fundamentals of electronics!
I read the patent application. He succeeded in finding an imbecile of an examiner, sure enough: even the initial “explanation” of how a motor works–describing how a “stator magnet” MUST attract a “rotor magnet” and overcome such-and-such drag to keep going–describes a hysteresis motor and ONLY a hysteresis motor. At that, it’s a p*ss-poor explanation . . .
wow!
Someone p*ssed in your wheaties this morning.
First, the author here of this web site is not John Bedini. It is someone who read his instructions on how to build the device mentioned in his patent. It looks like this site is just a way for the builder of the device to share his experiences.
Second, obviously no one is as smart as you. You seem to have it all figured out. I will make a suggestion, instead of taking the time to develop an entire essay about this guy, prove John Bedini wrong by building his device (exactly as he states) and then comment. Don’t act pious and talk down to everyone as if you know and they don’t.
Lastly, you seem to have a lot of anger in your post. When you make personal attacks, nobody will listen. Stick to the technical discussion and make your points.
Jesus is not in this conversation, so we can leave him out from this point forward.
no worries!!!! muhahahaha
I know I will get hit with some dis-believers and debunkers, it is ok when they post negative comments…in fact I encourage it! If they were smart enough they will realize the more they write their opinions and scientific knowledge about my project or even free energy on this webpage with their big point gathering scrabble words then the more this website will show up on a search engine top 10 to expose to the world that we don’t have to be enslaved by the power hungry and the scrabble trophy holders. So everyone give me all you got! You won’t hurt my feelings. This site and server is paid for by me. they cant cancel my subscription to spread the truth or even the research.
I answer to no one on this webpage. Dump your knowledge here and your links. I will keep all negative and positive comments free to the people, because the world will benefit from it.
Hm . . . I guess nobody here has the least understanding of electromagnetic theory. Magnetic fields are solenoidal, meaning that the field contours emerge from a north pole and return to a south pole. One can play games with topology so that only the north poles are exposed to a given armature circuit, but there will be zero flux linkage with that armature circuit and, consequently, no generated EMF from any changes to that flux linkage. I cannot help but notice that the putative “genius electrical engineer,” John Bedini, has difficulty spelling the most basic EE terminology; has zero understanding of high-school-level calculus; and states that “reactive power means di/dt.” I have no concept what the last of those statements might mean, but it sounds like a rather gross misunderstanding of the general concept that reactive components of current will be in quadrature phase to real components thereof, which is also true of the derivative (only if resolved onto an orthonormal frequency set basis, e.g., a Fourier expansion). Has anybody taken a look at what’s going on with the batteries and the power transistor and other things? Also, despite all these mentions of “Lenz’s Law” and such, I notice flagrant omissions from the putatively complete circuit diagram. Why don’t we include the ENTIRE system, and we’ll see where the energy comes from and where it goes. I’m reminded of a professor who used to stump sophomore circuits students with a simple capacitor-charging circuit and the question, “where did the energy go” when the initial and final electric field energies differ (I guess the students never heard of DOING WORK AGAINST AN ELECTRIC FIELD TO MOVE CHARGES FROM ONE CAPACITOR TO ANOTHER). This is such utter nonsense that it’s almost beneath commenting upon. And, of course, it’s such great technology, that’s why major firms have invested at least $0 to test it. Do you think they would spend a few dollars to build it were there ANY remotely serious claim to validity? Sorry to ramble quasi-ungrammatically, but I get angry thinking about how people here violate the commandment in Leviticus, “Thou shalt not . . . set a stumblingblock [sic] before the blind.” Oh, and the comments about “longitudinal waves” that are “not measurable” by our instruments are just utter nonsense.
Mr. Bedini, why don’t you post a COMPLETE circuit diagram for the ignorant–one that doesn’t leave unexplained black boxes floating around here and there while claiming that subsystem X “generates energy from nowhere.” I’m delighted that you achieved various things as a youngster and have had some success screwing with patents, but I hasten to note that a friend of mine quite literally patented amplitude modulation (by [a] calling it an Internet Aggregator and [b] finding a patent examiner who had zero understanding of how to trace signal spectra through a linear system)–you know, what happens with sidebands, aliasing, mixers, LPFs, block conversion, Hilbert transformers, things of that nature.
I also have a magic energy generating device that makes a motor spin and doesn’t have to be plugged in. You take the motor and connect its armature leads (the field circuit is parallel to the armature circuit) to a “magic” box that is clearly labeled “DON’T LOOK INSIDE HERE–IT ISN’T PART OF THE SYSTEM.”
J*sus Chr*st have mercy on the hopelessly ignorant . . .
Nice work
I am building the basic charger right now and have seen some of your videos and am very impressed. I am curious though, as the scoolgirl motor is not designed to develop torque (so I’m told), what is your aim with this setup? Are you able to charge more batteries with the many coils? I am not trying to be critical in any way, just curious about where you are going as I am not always the most perceptive
I am just learning this stuff and have been trying to comtemplate some of the applications of this circuitry and device although I have not completed my first charger yet (coil wire is backordered), but hope to within the next few weeks.
I have heard the window motor has some of the same capabilities to charge batteries, but also develops torque. Any thoughts on this?
Also came across a guy on Youtube names Dan Quale (pronounced kwalee) who developed a free spinning generator design which might lend itself to this type of motor.
Also, have been looking into the gray tube a bit and noticed a comment by a guy named robert calloway here:
http://www.keelynet.com about bedini’s circuits and the use of a spark gap to increase potential. Interesting stuff.
Then came across this document:
http://www.tfcbooks.com which goes into how tesla used the spark gap with magnets to increase the frequency of the discharge with lower potentials.
I’m not sure how all of this stuff fits together, but I thought you might be interested as it all seems very related to capturing and harnessing radiant energy. Keep up the good work.
Re: Welcome
Hi Mark,
Thanks for sharing so much information about the Bedini monople motor. Really good animation!
I’m just getting started building the battery charger and monopole motor charger shown in the book “Free Energy Generation” by Tom Bearden. Its a good read.
I will keep you posted as to my progress.
Again, thanks for all your hard work and sharing, Ron.
Hi, great job with your concise schematics. Do you have any email address? I tried to build a bedini SSG with 2 separate bifilar coils and the circuits completely separate, except for the 2 batteries. Did you try this? Some tuning help would be welcomed. Thanks
hello i am thierry morin. i dont know who have post my email but no problem if someone have solution… I am ok. Thierry
first contact.
Hello Sir, Following a different video I saw on your invention, I took the liberty to contact you. I am a businessman who has just sold his business and wish to take a new professional direction in relation to the struggle for global warming and the fight against pollution. I would have liked to share with you a simple idea which I think for years: the marketing of an invention for individuals (a lower price) providing a supply of energy to meet their needs with no pollution. This revolution, if it existed help solve real soon reversed pollution. I’ve already find funding to equip a unlimited credit every home, even those low-income … So that we can disseminate this invention throughout the world. I think it has long since the easiest way to quickly change the pollution of the planet, is to provide individuals with an invention energy "free" to help protect the environment, their purchasing power and their comfort. The need for information in an average home is between 5kVA and 30kVA. I am 42 years 4 children, very seriously with full powers to promote a concept as you see at the European level more … I’m trilingual, master the intricacies of the sale, communication, concepts in accounting and legal, with excellent presentation and extensive experience as a consultant (adviser) for (development oriented) and the Internet communication ( website, search engine …) … The relational acquired and cultivated throughout my short career to have my support is very important in my project … If your skill and invention are as interesting as it sounds I am concerned by our complementarity. With your knowledge with me and I know we could do "off" your invention. So if you thought your invention can be compatible with my "dream" … Pending the answer to my question and your feelings about this possible collaboration, Best regards Thierry Morin Fool is the one who invented a great thing because he just thought it was possible ADDRESS: Thierry Morin 31 rte de royan The 17,400 EGUILLES FRANCE Mobile: 33 6 88 07 26 42 email: thierry-morin@hotmail.fr
keep up. Free for the world.